{"title":"Victron Miscellaneous","description":"\u003cp\u003eVictron accessories and components that support an energy system installation but do not fit neatly into a single product category. This covers interface cables, communication leads, and connection hardware used across Victron inverter, charger, and monitoring setups, including VE.Direct, VE.Can, RJ45 and RS485-to-USB cables.\u003c\/p\u003e\u003cp\u003eTrade installers use this section to find the exact lead or adapter needed to link a Victron device to a monitoring system, laptop, or BMS, rather than browsing the whole Victron range. If you need a specific accessory and cannot see it listed, get in touch with our technical team and we will point you in the right direction.\u003c\/p\u003e","products":[{"product_id":"vecan-bms-type-a-cable-victron","title":"Victron VE.Can to CAN-bus BMS Type A Cable 1.8m | ASS030710118","description":"\u003cp\u003eThe VE.Can to CAN-bus BMS Type A Cable links Victron VE.Can devices to compatible CAN-bus BMS units using the Type A pinout. At 1.8 metres long, it gives enough reach for most battery cabinet and inverter layouts without leaving excess cable to manage. It suits installers integrating third-party BMS-equipped battery systems with Victron equipment.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, VE.Can (RJ45) to CAN-bus BMS Type A pinout\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1.8 m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.08 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030710118\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076071600\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, Victron devices with a VE.Can interface, including MultiPlus, Quattro and Cerbo GX where CAN-bus BMS communication is needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Can is Victron's implementation of the CAN-bus protocol, used to link inverter\/chargers, MPPT charge controllers, the Cerbo GX and other devices in a Victron system. When a third-party lithium battery uses a CAN-bus BMS, that BMS needs to pass state of charge, cell voltage limits and charge\/discharge parameters to the Victron system. This cable carries that link.\u003c\/p\u003e\u003cp\u003eThe Type A designation refers to the pinout on the BMS connector end. Not every CAN-bus BMS uses the same pinout, so check the BMS type before ordering. Type A appears on a number of common lithium battery brands, but always confirm against the BMS documentation first.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to connect third-party CAN-bus BMS lithium batteries to Victron VE.Can networks, in off-grid and hybrid solar installations pairing Victron inverter\/chargers with non-Victron batteries. Also fits battery cabinet builds where the BMS and Victron GX device sit within 1.8 m of each other, and marine or vehicle installations integrating CAN-bus BMS batteries with Victron equipment.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Can to CAN-bus BMS Type A Cable, 1.8 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eFit this cable with a qualified electrician or system integrator familiar with Victron VE.Can network setup. Confirm the BMS pinout type (Type A) against the battery manufacturer's documentation before connecting, as an incorrect pinout can cause communication failure or damage. CAN-bus termination resistors may be needed at each end of the VE.Can network depending on system layout; check your Victron system design for termination requirements.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060310536480,"sku":"ASS030710118","price":12.47,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030710118-1.webp?v=1785487753"},{"product_id":"victron-mk3-usb-ve-bus-interface","title":"Victron MK3-USB Interface VE.Bus to USB | ASS030140000","description":"\u003cp\u003eThe Victron MK3-USB interface connects a PC or laptop directly to the VE.Bus port on compatible Victron inverters and inverter\/chargers. It allows configuration, monitoring and firmware updates using VEConfigure and VEFlash software on Windows. Installers use it when commissioning or servicing Victron MultiPlus, MultiGrid and Quattro systems.\u003c\/p\u003e\u003ch2\u003eVictron interface MK3 USB key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\u003c\/strong\u003e, converts VE.Bus communication to USB for direct PC connection to Victron inverters and inverter\/chargers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Victron MultiPlus, MultiPlus-II, MultiGrid and Quattro product ranges.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoftware\u003c\/strong\u003e, supports configuration via VEConfigure and firmware updates via VEFlash on Windows.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.08 kg, easily carried in an installer's toolkit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection\u003c\/strong\u003e, plug-and-play USB, no external power supply needed from the PC side.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIdentification\u003c\/strong\u003e, SKU ASS030140000, GTIN 8719076019435, genuine Victron Energy product.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThe MK3-USB is the standard tool for accessing the VE.Bus communication port on Victron MultiPlus, MultiPlus-II, MultiGrid and Quattro inverter\/chargers. Without it, settings such as charge algorithms, input current limits, transfer switch behaviour and system configuration cannot be adjusted from a PC.\u003c\/p\u003e\u003cp\u003eVEConfigure, the main configuration tool for VE.Bus devices, communicates only via MK3-USB. VEFlash, used for firmware updates, does the same. Both run on Windows. The interface draws its operating power from the connected Victron device, so the PC's USB port doesn't need to supply power.\u003c\/p\u003e\u003cp\u003eIt does not offer real-time monitoring or data logging. For live monitoring, a GX device or VE.Bus Smart Dongle is the right choice instead. This interface is purely a configuration and firmware tool.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCommissioning and configuring Victron MultiPlus, MultiPlus-II, MultiGrid and Quattro inverter\/chargers on site.\u003c\/li\u003e\n\u003cli\u003eUpdating firmware on VE.Bus devices using VEFlash.\u003c\/li\u003e\n\u003cli\u003eAdjusting charge settings, input current limits and transfer switch parameters via VEConfigure.\u003c\/li\u003e\n\u003cli\u003eDiagnosing and reconfiguring existing installations during service visits.\u003c\/li\u003e\n\u003cli\u003eSetting up parallel and three-phase MultiPlus or Quattro systems needing PC-based configuration.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron MK3-USB interface (VE.Bus to USB)\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis is a configuration accessory and carries no mains or battery voltage. It connects between the RJ45 VE.Bus port on the Victron device and a USB port on a Windows PC. Configuration of inverter\/charger settings, particularly on grid-connected or parallel systems, should be done by a qualified installer familiar with VEConfigure. Incorrect configuration on grid-tied systems may affect G98 or G99 compliance, so always check settings against network operator requirements after changes.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060515369248,"sku":"ASS030140000","price":52.91,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030140000-1.webp?v=1785491110"},{"product_id":"victron-rj45-utp-cable-data","title":"Victron RJ45 UTP Cable 0.9m | VE.Direct Data Cable ASS030064920","description":"\u003cp\u003eThis 0.9 m RJ45 UTP cable from Victron Energy links compatible Victron devices that use RJ45 data ports. It suits short runs inside a panel or enclosure where an inverter\/charger, battery monitor or display needs a correctly wired data connection to another component.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.9 m, for connections within the same cabinet or wall-mounted area.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 on both ends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair) for low-voltage data communication.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.037 kg (37 g).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030064920. If this shows no stock, ASS030064921 is the equivalent replacement.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to link Victron inverter\/chargers to display or control panels, and to connect battery monitors to other system components. It carries data signals only, not mains or high-voltage power, and is common in off-grid, marine and vehicle installations where devices sit close together.\u003c\/p\u003e\u003ch3\u003eWhy use a Victron cable\u003c\/h3\u003e\u003cp\u003eA Victron-supplied cable has the correct pin assignment for the RJ45 interface. Third-party cables can use a different wiring layout, which leads to communication errors between devices. Longer lengths are available in the same series for connections that need more distance.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 0.9 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060521890080,"sku":"ASS030064920","price":7.13,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064920-1.webp?v=1785491941"},{"product_id":"victron-rs485-usb-cable-5m","title":"Victron RS485 to USB Interface Cable 5m | ASS030572050","description":"\u003cp\u003eThis Victron RS485 to USB interface cable creates a direct serial link between RS485-equipped Victron devices and a PC or laptop. At 5 metres long, it gives installers enough slack to reach equipment mounted in a cabinet or on a wall without having to work right next to the unit. It is used for configuration, monitoring and firmware updates on compatible Victron products.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable length\u003c\/strong\u003e, 5 metres\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterface\u003c\/strong\u003e, RS485 to USB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\u003c\/strong\u003e, draws power from the USB host, no external supply needed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, Victron devices with an RS485 port, including select MPPT solar chargers and inverters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoftware\u003c\/strong\u003e, works with VictronConnect and other Victron configuration tools on Windows, macOS and Linux where drivers are supported\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.187kg\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it for configuring and updating firmware on RS485-equipped Victron devices in the field, or for monitoring and diagnostics on off-grid and marine systems. It also suits bench testing and pre-configuration of equipment before it goes to site, and connecting to Victron MPPT chargers or inverters during commissioning.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis is a passive communication accessory. It carries no mains or high-voltage DC power, so no special electrical qualification is needed to connect it between a Victron device and a PC. Install the correct driver on your computer before use, and always follow Victron's guidance when updating firmware on a live system, confirming the device is in a safe state first.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x RS485 to USB interface cable, 5m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060524675360,"sku":"ASS030572050","price":25.18,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030572050-1.webp?v=1785492350"},{"product_id":"split-phase-autotransformer-32a","title":"Victron Autotransformer 120\/240V-32A Split-Phase | ITR000100001","description":"\u003cp\u003eThe Victron Autotransformer 120\/240V-32A converts a single 240V AC source into a balanced 120V\/120V split-phase supply, or combines two 120V legs into 240V. Rated at 32A continuous, it suits off-grid, marine and North American-standard electrical installations that need split-phase distribution from a single-phase source.\u003c\/p\u003e\u003ch2\u003eVictron autotransformer key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage conversion\u003c\/strong\u003e: splits 240V single-phase into 120V\/240V split-phase output, or combines two 120V legs into 240V.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContinuous rating\u003c\/strong\u003e: 32A, suited to substantial loads across both legs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAutotransformer design\u003c\/strong\u003e: shared-winding construction is more compact than a full isolation transformer, though it does not provide galvanic isolation between input and output.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eToroidal core\u003c\/strong\u003e: keeps no-load losses low and reduces audible hum.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e: 12.8 kg, reflecting a substantial copper-wound core for the rated current.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverter compatibility\u003c\/strong\u003e: works alongside Victron MultiPlus or Quattro units, allowing split-phase output from a single 240V inverter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eFitted in off-grid systems using North American-standard 120V\/240V distribution panels, in marine and yacht installations needing split-phase AC from one inverter, and in RV builds where appliances expect a balanced split-phase supply. It also covers light commercial off-grid sites with mixed 120V and 240V loads. At 32A and 240V, maximum throughput is approximately 7.68 kVA, covering most residential and light commercial off-grid demands.\u003c\/p\u003e\u003ch3\u003eIsolation and installation\u003c\/h3\u003e\u003cp\u003eBecause primary and secondary windings share a connection, this unit does not isolate input from output electrically. Where isolation is a safety or regulatory requirement, a separate isolation transformer is needed instead. Installation should be carried out by a qualified electrician, with wiring and overcurrent protection rated for the full 32A load on both sides.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Autotransformer 120\/240V-32A (ITR000100001)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060525199648,"sku":"ITR000100001","price":380.08,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-itr000100001-1.webp?v=1785492402"},{"product_id":"victron-ve-direct-usb-interface","title":"VE.Direct to USB Interface | Victron Energy ASS030530010","description":"\u003cp\u003eThe VE.Direct to USB interface links any Victron Energy device fitted with a VE.Direct port to a Windows, Mac or Linux computer over USB. It's the standard tool installers reach for when commissioning MPPT solar charge controllers, BMV battery monitors or Phoenix inverters using Victron's VictronConnect software.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConverts VE.Direct serial communication to a standard USB Type-A connection\u003c\/li\u003e\n\u003cli\u003eWorks with any Victron product fitted with a VE.Direct port, including MPPT controllers, BMV battery monitors and Phoenix inverters\u003c\/li\u003e\n\u003cli\u003eUsed with VictronConnect for configuration, live monitoring and firmware updates\u003c\/li\u003e\n\u003cli\u003ePlug-and-play on Windows, macOS and Linux, no drivers typically required\u003c\/li\u003e\n\u003cli\u003eWeighs 60 g, easy to carry for site visits\u003c\/li\u003e\n\u003cli\u003eSKU ASS030530010, GTIN 8719076019589\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eInstallers use this cable for on-site commissioning of MPPT solar charge controllers, pushing firmware updates to VE.Direct-compatible devices, and pulling live data on a laptop when diagnosing a fault. It also covers BMV battery monitor setup and Phoenix inverter configuration where no GX device is fitted.\u003c\/p\u003e\u003ch3\u003eNot a permanent monitoring link\u003c\/h3\u003e\u003cp\u003eThis cable is a configuration and diagnostic accessory rather than a monitoring cable for continuous use. For remote or persistent monitoring, a GX device is the correct product, not this interface.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003ePlug the interface into the VE.Direct port on the target device and into a free USB port on the computer, then open VictronConnect. Check Victron's release notes for the current VictronConnect version before use.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Direct to USB interface cable (ASS030530010)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060528279840,"sku":"ASS030530010","price":23.08,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530010-1.webp?v=1785492800"},{"product_id":"victron-ve-direct-data-cable","title":"Victron VE.Direct Cable 1.8m Data Cable | ASS030530218","description":"\u003cp\u003eThe Victron VE.Direct Cable links VE.Direct-compatible devices to each other, or to a computer, phone or display, for monitoring and configuration. At 1.8 metres it suits panel-mounted and cabinet installations where the device and monitoring interface sit close together.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1.8m, suited to short to medium-distance runs between VE.Direct devices and monitoring equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with all Victron products using the VE.Direct port, including BMV battery monitors, SmartSolar MPPT charge controllers and Phoenix inverters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eData and power\u003c\/strong\u003e, carries both over the VE.Direct interface, allowing configuration and live monitoring without a separate power supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUsed with\u003c\/strong\u003e, the VE.Direct to USB interface or VE.Direct Bluetooth Smart dongle to connect devices to VictronConnect or the VRM Portal.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 55g, with a compact connector profile for tight cable spaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number\u003c\/strong\u003e, ASS030530218, GTIN 8719076019619.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's own serial communication protocol, used across their product range. The cable uses a dedicated connector at each end and passes data between devices such as MPPT charge controllers, BMV battery monitors and Phoenix inverters. It is the physical link required before any VE.Direct adapter, whether USB, Bluetooth or RS232, can function.\u003c\/p\u003e\u003cp\u003eThe 1.8m length is the most commonly specified option where the charge controller or inverter sits within roughly a metre of the monitoring display or interface dongle. Victron also offers 3m and 5m variants for longer runs. This cable carries no mains or battery power; it is a data cable only.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a SmartSolar or BlueSolar MPPT charge controller to a BMV battery monitor for combined system data.\u003c\/li\u003e\n\u003cli\u003eLinking a Phoenix inverter or MPPT to a VE.Direct to USB interface for configuration via VictronConnect on a laptop or PC.\u003c\/li\u003e\n\u003cli\u003eConnecting devices to a Cerbo GX or Color Control GX for system integration and VRM Portal monitoring.\u003c\/li\u003e\n\u003cli\u003eOff-grid and mobile installations, including narrowboats, motorhomes and remote cabins, using Victron VE.Direct devices.\u003c\/li\u003e\n\u003cli\u003eReplacing a damaged or missing cable in an existing Victron installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Direct Cable, 1.8m (ASS030530218)\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis is a low-voltage data cable, not a mains or high-current battery cable. It can be connected and disconnected without specialist electrical knowledge. Check that the VE.Direct port on each device is free before connecting. If it forms part of a larger solar or battery system, the wider installation should be carried out by a qualified electrician or MCS-accredited installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060529656096,"sku":"ASS030530218","price":8.49,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530218-1.webp?v=1785492958"},{"product_id":"victron-rj45-utp-cable-1-8m","title":"Victron RJ45 UTP Cable 1.8m for GX Devices | ASS030064950","description":"\u003cp\u003eThis Victron RJ45 UTP cable is a 1.8 m straight-through data cable used to link compatible Victron Energy devices through their RJ45 communication ports. It's a data-only cable, not a power lead, and is built for the short runs needed inside cabinets, enclosures or between adjacent panels.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1.8 m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 at both ends\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.075 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030064950 (if unavailable, the equivalent replacement is ASS030064951)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed throughout Victron installations to carry communication signals between devices such as inverter\/chargers, battery monitors and GX units like the Cerbo GX or Color Control GX. The 1.8 m length works well where the connected devices sit close together, such as within one enclosure or on a neighbouring wall panel. It also serves as replacement cabling where an existing lead has failed or is too short, and suits off-grid, marine and vehicle system builds using Victron components.\u003c\/p\u003e\u003ch3\u003eCompatibility note\u003c\/h3\u003e\u003cp\u003eThe connector looks like a standard Ethernet patch cable, but this lead is intended for Victron's own inter-device communication wiring rather than internet connectivity. Check the port type and communication protocol on your specific devices before ordering.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron RJ45 UTP Cable, 1.8 m (ASS030064950)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52060750479648,"sku":"ASS030064950","price":7.09,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064950-1.webp?v=1785502853"},{"product_id":"victron-ve-direct-data-cable-3m","title":"Victron VE.Direct Cable 3m | ASS030530230","description":"\u003cp\u003eThe Victron VE.Direct Cable is a data communication lead for linking Victron devices fitted with a VE.Direct port. At 3 metres, it suits installations where connected units sit a short distance apart, such as a charge controller and a GX display mounted in the same enclosure or cabinet.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 3 metres\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterface\u003c\/strong\u003e, VE.Direct\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.115 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, VE.Direct-equipped devices including BMV battery monitors, SmartSolar MPPT charge controllers and Phoenix inverters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrigin\u003c\/strong\u003e, genuine Victron Energy accessory\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's own serial communication interface, used to pass data between devices such as an MPPT charge controller and a Colour Control GX, GlobalLink 520 or a computer running VictronConnect. A correctly rated, properly terminated cable is needed for this link to work. This 3m length is a common choice where the monitoring unit or GX device sits close to the charge controller or battery monitor, with enough slack to route neatly through an enclosure without excess cable. Other lengths are available in the VE.Direct range for longer or shorter runs.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a SmartSolar or BlueSolar MPPT charge controller to a Cerbo GX or Colour Control GX\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a GX device for system-level monitoring\u003c\/li\u003e\n\u003cli\u003eConnecting a Phoenix inverter with a VE.Direct port to a monitoring or control unit\u003c\/li\u003e\n\u003cli\u003eInterfacing a VE.Direct device with a laptop or Raspberry Pi via a VE.Direct to USB adapter, running VictronConnect or Venus OS\u003c\/li\u003e\n\u003cli\u003eOff-grid cabin, narrowboat, motorhome and marine installations where Victron components sit close together\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron VE.Direct Cable, 3m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003ePlug the cable directly into the VE.Direct ports on compatible devices; no tools are needed. Power down both devices before connecting or disconnecting where possible. The cable carries data only and does not supply power. Wider solar PV or battery system work should be carried out by a qualified electrician or MCS-accredited installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061009674528,"sku":"ASS030530230","price":10.21,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530230-1.webp?v=1785508396"},{"product_id":"victron-rj45-utp-cable-1-8-metre","title":"Victron RJ45 UTP Cable 1.8m for VE.Bus Devices | ASS030064951","description":"\u003cp\u003eThis Victron Energy RJ45 UTP cable connects compatible Victron devices through their RJ45 communication ports. At 1.8 m long, it suits panel, cabinet and wall-mounted setups where the units sit close together.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1.8 m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 at both ends\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.075 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, VE.Bus and VE.Net ports on Victron equipment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eMany Victron inverters, chargers, battery monitors and system panels use RJ45 ports with standard UTP cabling. This cable gives a direct plug-and-play connection between those ports, so there is no need to crimp a custom lead or gamble on a generic patch cable with the wrong pinout.\u003c\/p\u003e\u003cp\u003eThe 1.8 m length works for most rack, cabinet or wall-panel jobs where the devices are mounted near each other. Victron also offers longer lengths for runs between separate enclosures or rooms. Because this is a low-voltage signal cable, it should be routed away from high-current DC or AC conductors where practical.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a MultiPlus or Quattro inverter\/charger to a Color Control GX or Cerbo GX\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a system display panel\u003c\/li\u003e\n\u003cli\u003eCommunication links within a VE.Bus network in off-grid systems\u003c\/li\u003e\n\u003cli\u003eReplacing a lost or damaged cable in an existing Victron installation\u003c\/li\u003e\n\u003cli\u003eShort-run connections in marine, motorhome and vehicle power systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 1.8 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis cable carries low-voltage communication signals only, not mains or high-voltage DC power. It can be fitted or removed without specialist electrical qualifications. Keep it clear of high-current cabling where you can, and check the correct port and pinout on each device against the Victron manual before connecting.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061010428192,"sku":"ASS030064951","price":7.78,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064951-1.webp?v=1785508511"},{"product_id":"rj45-utp-patch-cable-victron","title":"Victron Energy RJ45 UTP Patch Cable 0.9m for GX Devices | ASS030064921","description":"\u003cp\u003eThis Victron Energy RJ45 UTP cable is a 0.9 m patch lead for linking compatible Victron devices through their RJ45 communication ports. It suits installers wiring GX devices, inverter\/chargers and battery monitors that sit close together, such as inside a single cabinet or on a compact wall-mounted board.\u003c\/p\u003e\u003ch2\u003eVictron RJ45 cable key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.9 m, suited to short runs between adjacent devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 plugs at both ends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction\u003c\/strong\u003e, UTP (Unshielded Twisted Pair) for signal integrity over short distances.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 37 g.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030064921.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it to connect a Victron GX device to a compatible inverter\/charger or battery monitor over RJ45, or as a short communication link within a battery enclosure or wall-mounted system board. It also works as a replacement for a lost or damaged original cable, or as spare stock for installers building several Victron systems.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis is a communication cable only and must never be used for power connections. Confirm both RJ45 ports are communication ports before connecting, and check the wiring diagram supplied with each Victron device before completing a system. A qualified installer should commission the finished solar or battery installation.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 0.9 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061010821408,"sku":"ASS030064921","price":6.65,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064921-1.webp?v=1785508615"},{"product_id":"ve-direct-cable-right-angle-0-9m","title":"Victron VE.Direct Cable 0.9m Right Angle Connector | ASS030531209","description":"\u003cp\u003eA 0.9m VE.Direct cable with a right angle connector on one end and a straight connector on the other, used to link Victron devices that communicate over the VE.Direct protocol. It suits MPPT solar charge controllers, BMV battery monitors and Phoenix inverters connecting to compatible displays, interfaces or other VE.Direct-enabled equipment.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.9m, suited to short runs between adjacent devices or panels.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRight angle connector\u003c\/strong\u003e, one end, for flush mounting against walls, enclosures or tight cabinets.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStraight connector\u003c\/strong\u003e, opposite end, fits any standard VE.Direct port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with all Victron devices using the VE.Direct interface, including MPPT charge controllers, BMV monitors and Phoenix inverters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 25g.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eThe right angle end reduces the clearance needed behind a device, which helps in flush-mounted enclosures, narrow battery cabinets or anywhere a straight exit would strain the cable or block a panel door. Typical uses include connecting an MPPT controller to a Color Control GX or Cerbo GX in a compact enclosure, linking a BMV battery monitor to a GX device or VE.Direct to USB interface, or wiring a Phoenix inverter to a monitoring display where space is limited. It also suits off-grid battery cabinets, narrowboats, motorhomes and marine installations.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis cable carries data only; it does not supply power to connected devices. Power down both devices before connecting or disconnecting, since VE.Direct ports are not hot-swap rated on all equipment. Check the relevant device documentation first. No special electrical qualification is needed to fit this cable, though the wider installation, inverters, charge controllers and battery connections, should be handled by a qualified electrician or competent person.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x VE.Direct cable, 0.9m, with one right angle connector and one straight connector\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061010952480,"sku":"ASS030531209","price":9.12,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030531209-1.webp?v=1785508661"},{"product_id":"victron-rj45-utp-cable-3-metre","title":"Victron RJ45 UTP Cable 3m for VE.Bus Communication | ASS030064981","description":"\u003cp\u003eThe Victron RJ45 UTP Cable is a 3 metre unshielded twisted pair cable with RJ45 connectors at both ends, used to link compatible Victron devices over their RJ45 communication ports.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 3 m, enough reach for most panel, cabinet and enclosure installations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 at both ends, compatible with Victron devices that use RJ45 communication ports.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction\u003c\/strong\u003e, UTP (unshielded twisted pair), suited to low-voltage data communication between Victron components.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.12 kg, easy to route and manage within an installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Victron Energy accessory\u003c\/strong\u003e, compatibility with supported products in the Victron ecosystem.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eRJ45 UTP cables carry communication signals between Victron devices such as inverter\/chargers, battery monitors, solar charge controllers and display panels. The RJ45 port on this equipment typically carries VE.Bus or similar proprietary protocols, so cable type and length matter for signal integrity.\u003c\/p\u003e\u003cp\u003eAt 3 metres, this cable suits components mounted close together, such as within a single enclosure or across adjacent wall-mounted units. UTP construction is adequate for the low-noise environments typical of residential and light commercial battery rooms or plant rooms. For longer runs or environments with significant electrical interference, a shielded alternative may be more appropriate.\u003c\/p\u003e\u003ch3\u003eTypical uses\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eConnecting a MultiPlus or Quattro inverter\/charger to a Color Control GX or Cerbo GX.\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a GX device or display panel.\u003c\/li\u003e\n\u003cli\u003eWiring SmartSolar or BlueSolar charge controllers to system communication hubs.\u003c\/li\u003e\n\u003cli\u003eReplacement cable where an existing one has been damaged or is too short.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 3 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eEnsure the RJ45 connectors are fully seated and latched at both ends before powering the system, and check that connected devices use compatible RJ45 ports. Route away from high-current DC cables where possible. Complex or high-voltage installation work should be carried out by a qualified electrician or accredited installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061011181856,"sku":"ASS030064981","price":8.2,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064981-1.webp?v=1785508711"},{"product_id":"ve-direct-cable-03m-connector","title":"Victron VE.Direct Cable 0.3m Data Cable | ASS030530203","description":"\u003cp\u003eThe Victron VE.Direct Cable is a short-run data cable that links VE.Direct-compatible Victron devices together or to a monitoring accessory. At 0.3m it is the shortest cable in the range, intended for devices mounted side by side in the same panel or enclosure.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.3m, for short-distance connections between closely mounted devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtocol\u003c\/strong\u003e, uses the VE.Direct communication interface found on BMV battery monitors, MPPT charge controllers and Phoenix inverters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle cable\u003c\/strong\u003e, carries both data and power, so no extra wiring is needed for communication.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 15g (0.015kg), adding almost nothing to an installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, standard VE.Direct connector fitted at both ends with a positive-locking fit.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron Energy's own point-to-point communication interface, used to pass data between devices such as MPPT charge controllers, BMV battery monitors and VE.Direct to USB or Bluetooth Smart Dongle accessories. Because it is point-to-point, each cable links exactly one device to one other device or accessory. If several VE.Direct devices need to reach a single monitoring point, such as a Cerbo GX, each one needs its own cable. The 0.3m length suits cabinets, enclosures or DIN rail layouts where two devices sit right next to each other.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting an MPPT solar charge controller to a VE.Direct to USB interface or Bluetooth Smart Dongle mounted alongside it.\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a Cerbo GX or other GX device in the same enclosure.\u003c\/li\u003e\n\u003cli\u003eShort data runs in compact off-grid systems, campervan builds and marine electrical panels.\u003c\/li\u003e\n\u003cli\u003eConnecting a Phoenix inverter to a VE.Direct monitoring accessory where space is tight.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron VE.Direct Cable, 0.3m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis cable carries low-voltage data signals only, so no specialist electrical installation is needed. Power down both devices before connecting or disconnecting VE.Direct cables, and check both ends are genuinely VE.Direct compatible: the connector shape can resemble other connectors that are not interchangeable with it.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061011837216,"sku":"ASS030530203","price":8.98,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530203-1.webp?v=1785508801"},{"product_id":"victron-ve-direct-data-cable-0-9m","title":"Victron VE.Direct Cable 0.9m Data Cable | ASS030530209","description":"\u003cp\u003eThe Victron VE.Direct Cable connects VE.Direct-compatible Victron devices for monitoring, configuration and data transfer. At 0.9 metres, it's built for installations where components sit close together, such as a shared enclosure or DIN rail panel.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.9m, the shortest option in the VE.Direct cable range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, connects any two VE.Direct-compatible Victron devices, including MPPT solar charge controllers, BMV battery monitors and Phoenix inverters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtocol\u003c\/strong\u003e, uses the VE.Direct serial communication protocol for real-time data transfer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApp support\u003c\/strong\u003e, works with VictronConnect when paired with a VE.Direct to USB or VE.Direct to Bluetooth Smart dongle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 25g (0.025kg).\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it to link an MPPT SmartSolar or BlueSolar charge controller to a BMV battery monitor, or connect a Phoenix inverter to a VE.Direct panel. It also works for connecting a VE.Direct device to a Raspberry Pi or computer via a VE.Direct to USB interface, or for wireless monitoring with a VE.Direct Bluetooth Smart dongle. It suits off-grid and mobile setups where devices share a single battery box or enclosure.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis is a data cable only, it does not carry mains or battery power. It can be fitted or removed without specialist tools, but the correct VE.Direct port must be used on each device with the connector fully seated. For full system commissioning involving inverters, charge controllers or battery connections, use a qualified electrician or accredited installer.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x Victron VE.Direct Cable, 0.9m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061013279008,"sku":"ASS030530209","price":9.12,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530209-1.webp?v=1785508981"},{"product_id":"victron-rj45-utp-communication-cable","title":"Victron RJ45 UTP Cable 5m Communication Cable | ASS030065001","description":"\u003cp\u003eThis Victron Energy RJ45 UTP cable runs 5 metres and connects compatible Victron devices through their RJ45 communication ports. It suits installers wiring inverter\/chargers, battery monitors, solar charge controllers and display panels together where a stable data link between components is needed.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 5 m, giving flexibility when devices are not mounted close together.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 on both ends, compatible with Victron devices using RJ45 communication ports.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair), suited to low-noise indoor installations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.172 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Victron accessory\u003c\/strong\u003e, compatible with supported Victron products.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to connect Victron inverter\/chargers to remote control panels or displays, link battery monitors to system components, and wire solar charge controllers to monitoring devices in off-grid and hybrid setups. It also works as general RJ45 communication cabling across a Victron installation.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eCheck that the target devices use a standard RJ45 communication port before fitting. Route the cable away from high-current DC or AC wiring to reduce interference. Complex or high-voltage systems should be wired and commissioned by a qualified installer.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 5 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061013573920,"sku":"ASS030065001","price":13.37,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030065001-1.webp?v=1785509049"},{"product_id":"victron-rs485-usb-interface-cable","title":"Victron RS485 to USB Interface Cable 1.8m | ASS030572018","description":"\u003cp\u003eThe Victron RS485 to USB interface cable gives a direct serial link between RS485-equipped Victron devices and a PC or laptop. Installers use it to configure, monitor or update firmware on compatible Victron equipment without a native RS485 port on the computer.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterface\u003c\/strong\u003e, converts RS485 serial signals to USB for connection to a standard PC or laptop.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable length\u003c\/strong\u003e, 1.8m, enough to reach a laptop from wall-mounted or rack-mounted equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\u003c\/strong\u003e, draws power from the USB bus, no external power supply required.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 67.3g, compact enough to carry in a tool kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Victron devices fitted with an RS485 communication port.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed for configuring Victron inverters, chargers and other RS485-equipped devices from a laptop on site, and for firmware updates on compatible Victron products. Also suited to monitoring and diagnostics during commissioning of off-grid and solar installations, or bench testing equipment before it goes out to site.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnect the RS485 end to the port on the Victron device and the USB end to the computer. Depending on the operating system, USB drivers may need installing before the interface is recognised. Make sure the Victron device is in a safe state before connecting or disconnecting communication cables during a live installation.\u003c\/p\u003e\u003ch2\u003eWhat's included\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron RS485 to USB interface cable, 1.8m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061014720800,"sku":"ASS030572018","price":24.05,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030572018-1.webp?v=1785509214"},{"product_id":"victron-rj45-utp-cable-03m","title":"Victron RJ45 UTP Cable 0.3m for VE.Bus \u0026 VE.Can | ASS030064901","description":"\u003cp\u003eA short RJ45 UTP patch cable from Victron Energy for linking compatible Victron devices over short distances. At 0.3 m, it suits installers wiring components inside a panel, enclosure or cabinet where a full-length cable would leave unnecessary slack.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.3 m, for short-run connections between adjacent devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, RJ45, compatible with Victron VE.Bus, VE.Can and other RJ45-based communication ports.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair), for low-voltage data communication.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.03 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Victron Energy accessory\u003c\/strong\u003e, made to fit Victron's communication interface specifications.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to link Victron devices sharing a communication port over a short distance. Typical examples include connecting a MultiPlus or Quattro to a GX device such as a Cerbo GX or Color Control GX mounted in the same enclosure, joining Victron components on a DIN rail or backplate, or linking a BMV battery monitor to a nearby display. It works well in compact off-grid or marine panels where a longer cable would create excess slack.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis cable carries data signals only, not power. Check that the RJ45 ports on both devices are clean and undamaged before connecting. Where possible, keep it away from high-current DC cabling to reduce the risk of interference on the communication line.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 0.3 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061014982944,"sku":"ASS030064901","price":7.13,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030064901-1.webp?v=1785509250"},{"product_id":"ve-direct-cable-right-angle-1-8m","title":"Victron VE.Direct Cable 1.8m Right Angle Connector | ASS030531218","description":"\u003cp\u003eA 1.8m VE.Direct cable for linking Victron Energy devices that use the VE.Direct communication protocol. One end has a right angle connector, useful where space is tight or the cable needs a low-profile exit from the device port.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1.8m cable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, one right angle, one straight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 45g\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, any Victron device with a VE.Direct port, including BMV battery monitors, SmartSolar MPPT charge controllers and Phoenix inverters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030531218\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076019671\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's point-to-point interface for passing data between compatible devices and monitoring gear such as a Color Control GX, Cerbo GX, or a PC running VictronConnect. This cable carries that link over a 1.8m run, enough for most standard enclosure and wall-mount layouts without excess slack.\u003c\/p\u003e\u003cp\u003eThe right angle connector at one end eases strain on the port where the cable must exit horizontally, or where a straight plug would foul against a panel, wall or nearby component. That matters in compact battery enclosures, van conversions and marine installs where routing space is limited.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting SmartSolar or BlueSolar MPPT charge controllers to a GX device or VE.Direct to USB interface\u003c\/li\u003e\n\u003cli\u003eLinking BMV battery monitors to a Cerbo GX or Color Control GX in tight enclosures\u003c\/li\u003e\n\u003cli\u003eConnecting Phoenix inverters to monitoring or display equipment\u003c\/li\u003e\n\u003cli\u003eVan, motorhome and marine installations with restricted cable routing around the device port\u003c\/li\u003e\n\u003cli\u003eReplacing a damaged or missing VE.Direct cable in an existing Victron system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x VE.Direct cable, 1.8m, one right angle connector and one straight connector\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003ePower down both devices before connecting or disconnecting. Orient the right angle connector to suit your cable exit direction. VE.Direct is data-only and carries no power. Fitting the cable itself needs no special qualification, though associated electrical work on solar, battery and inverter systems should be done by a qualified installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061065609504,"sku":"ASS030531218","price":9.26,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030531218-1.webp?v=1785510621"},{"product_id":"victron-rj12-cable-09m","title":"Victron RJ12 UTP Communication Cable 0.9m | ASS030066010","description":"\u003cp\u003eThe Victron RJ12 UTP Cable is a 0.9 m data lead fitted with RJ12 connectors at each end, used to link compatible Victron Energy devices that communicate over the RJ12 (6P6C) interface.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ12 (6P6C) on both ends\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.9 m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.025 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030066010\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076071532\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eRJ12 is a 6-position, 6-contact connector format used across several Victron Energy products for data and communication wiring. This cable arrives ready-terminated, so there is no need for field crimping or custom assembly. The UTP construction uses twisted pairs to reduce interference on data lines, which matters in enclosures where other cabling sits nearby.\u003c\/p\u003e\u003cp\u003eAt 0.9 m the cable suits devices mounted close together, such as within a single enclosure or on an adjacent panel.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting Victron battery monitors to compatible display or control units\u003c\/li\u003e\n\u003cli\u003eData wiring between Victron inverter\/chargers and remote panels in the same enclosure\u003c\/li\u003e\n\u003cli\u003eShort RJ12 communication links in off-grid, marine and vehicle power systems\u003c\/li\u003e\n\u003cli\u003eReplacement or spare cable for existing Victron installations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x RJ12 UTP Cable, 0.9 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis cable carries data signals only, not mains or high-voltage power. Route it away from high-current DC cables where possible to reduce interference, and confirm both devices use the RJ12 (6P6C) interface before fitting. For full system work involving inverters, battery banks or grid connections, use a qualified electrician or MCS-accredited installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061065642272,"sku":"ASS030066010","price":6.71,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030066010-1.webp?v=1785510628"},{"product_id":"victron-vecan-canbus-bms-type-a-cable","title":"Victron VE.Can to CAN-bus BMS Type A Cable 5m | ASS030710150","description":"\u003cp\u003eThis Victron cable links a VE.Can-equipped GX device to a CAN-bus BMS Type A battery system, giving the two components a direct data connection. At 5 metres, it suits installations where the GX device and BMS sit some distance apart, such as larger enclosures or separate battery and inverter cabinets.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 5 m, the longer of Victron's standard options for this connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection\u003c\/strong\u003e, VE.Can to CAN-bus BMS Type A, with correctly pinned connectors for plug-and-play wiring.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.22 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030710150.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076071617.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it to connect Victron GX devices such as the Cerbo GX or Venus GX to a CAN-bus Type A BMS battery system. Common in off-grid and hybrid solar installations with managed lithium battery banks, marine and vehicle builds where the GX device and BMS are mounted apart, and commercial storage cabinets that need a longer cable run.\u003c\/p\u003e\u003ch3\u003eType A vs Type B\u003c\/h3\u003e\u003cp\u003eCAN-bus BMS Type A uses a different pin assignment to Type B. The two are not interchangeable, and using the wrong cable means no communication or incorrect data between the GX device and the BMS. Confirm which type your BMS uses before ordering.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Can to CAN-bus BMS Type A Cable, 5 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eConnect with the system powered down. On lithium battery systems, grid-tied inverters or high-voltage DC equipment, commissioning should be carried out by a qualified installer familiar with Victron system configuration.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061065806112,"sku":"ASS030710150","price":12.47,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030710150-1.webp?v=1785510662"},{"product_id":"stainless-shore-power-inlet-16a","title":"Victron Power Inlet Stainless Steel 16A\/250Vac (2P\/3W) | SHP301602000","description":"\u003cp\u003eA stainless steel shore power inlet from Victron Energy, rated 16A\/250Vac in a 2-pole, 3-wire configuration. It gives boats, motorhomes and off-grid buildings a fixed, weatherproof connection point for shore power or generator supply.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial\u003c\/strong\u003e, stainless steel body resists corrosion in marine and outdoor settings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 16A\/250Vac for standard single-phase shore power loads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfiguration\u003c\/strong\u003e, 2-pole, 3-wire (2P\/3W), carrying live, neutral and earth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCover\u003c\/strong\u003e, hinged protective cover seals the socket when not plugged in.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e, panel or flush mounting for a permanent installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with standard 16A shore power plugs and cables used across the UK and EU.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eFitted as a shore power inlet on sailing yachts, motorboats and narrowboats, or as an external power connection point on motorhomes and campervans. It also serves as a generator hookup inlet for off-grid cabins and static structures, and as a replacement inlet on existing marine or vehicle electrical panels.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eFitting should be carried out by a qualified electrician or competent marine electrical engineer, with correct panel cutout dimensions and cable sizing for 16A AC circuits. The earth conductor must be connected, and the cover kept closed and latched whenever the inlet is not in use.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Stainless steel power inlet 16A\/250Vac (2P\/3W) with protective cover\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061066035488,"sku":"SHP301602000","price":74.52,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp301602000-1.webp?v=1785510689"},{"product_id":"victron-rj45-utp-cable-10-metre","title":"Victron RJ45 UTP Cable 10m for VE.Bus \u0026 GX Devices | ASS030065011","description":"\u003cp\u003eThis Victron Energy RJ45 UTP cable runs 10 metres and connects compatible Victron devices over a standard RJ45 interface. It suits installers who need a longer cable run between communication network components.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 10 metres\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ45 at both ends, compatible with VE.Bus, VE.Net and other RJ45-based Victron communication ports\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair), carries data signals rather than power\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection\u003c\/strong\u003e, plug and play, no crimping or extra tools needed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.36 kg\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to link Multi or Quattro inverter\/chargers to a Color Control GX, CCGX or other GX device, and for VE.Bus wiring between Victron system components. The 10-metre length is the longest standard option in Victron's UTP cable range, useful where equipment is spread across a larger space such as a battery room, plant room or marine electrical panel. It also works as a replacement where an existing cable is damaged or too short.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis cable carries data signals only. Check that the RJ45 ports on your Victron equipment match before connecting, as not all RJ45 ports on Victron devices are interchangeable. Full system wiring should be carried out by someone familiar with Victron Energy installations.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ45 UTP Cable, 10 metres\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061066854688,"sku":"ASS030065011","price":16.04,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030065011-1.webp?v=1785510833"},{"product_id":"victron-ve-direct-cable-5-metre","title":"Victron VE.Direct Cable 5m | ASS030530250","description":"\u003cp\u003eThe Victron VE.Direct Cable (5m) connects VE.Direct-compatible devices to each other or to a monitoring interface such as the Color Control GX, Cerbo GX, or a PC via a VE.Direct to USB adapter. Installers use it to pass data between Victron components across longer cable runs within a system enclosure or installation.\u003c\/p\u003e\u003ch2\u003eVictron ve direct cable key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 5 metres, for installations where components are not close together.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtocol\u003c\/strong\u003e, uses the VE.Direct proprietary serial communication protocol for data transfer between Victron devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with MPPT solar charge controllers, BMV battery monitors, Phoenix inverters, and SmartSolar chargers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, terminated with VE.Direct connectors at both ends, ready to use without modification.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.185 kg.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's point-to-point serial communication interface. It carries data and, on some devices, a small supply voltage, transmitting real-time operating data such as state of charge, voltage, current, and fault codes between devices. It is the standard wiring method for connecting BMV monitors, MPPT controllers, and Phoenix inverters to a GX device or a laptop running VictronConnect.\u003c\/p\u003e\u003cp\u003eThis 5m length is the longest standard VE.Direct cable in the Victron range, suited to installations where the charge controller, battery monitor, or inverter sits at a distance from the GX device or monitoring panel. The right length avoids coiling excess cable and removes the need for custom fabrication.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting an MPPT solar charge controller to a Cerbo GX or Color Control GX where components are mounted apart.\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a GX device for system-wide state-of-charge monitoring.\u003c\/li\u003e\n\u003cli\u003eConnecting a Phoenix inverter to a monitoring or control interface via VE.Direct.\u003c\/li\u003e\n\u003cli\u003eData logging and configuration via a VE.Direct to USB adapter connected to a laptop or Raspberry Pi running Venus OS.\u003c\/li\u003e\n\u003cli\u003eOff-grid, marine, and vehicle installations where panel-mounted GX devices sit away from battery or charge controller compartments.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron VE.Direct Cable, 5m\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003ePower down both devices before connecting or disconnecting VE.Direct cables; the port is not designed for hot-swapping under load. Route cables away from high-current DC wiring to avoid interference. Each VE.Direct port supports one connection at a time, so multiple devices connecting to a single GX unit each need their own port or a dedicated USB adapter.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061067378976,"sku":"ASS030530250","price":11.24,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530250-1.webp?v=1785510941"},{"product_id":"victron-rj45-terminator-vecan","title":"Victron VE.Can RJ45 Terminator Bag of 2 | ASS030700000","description":"\u003cp\u003eThe Victron VE.Can RJ45 terminator is a passive network component used to correctly terminate a VE.Can bus. Sold as a bag of two, it suits installers setting up Victron systems where several devices share a single VE.Can network.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\u003c\/strong\u003e, terminates a VE.Can network bus at both ends to prevent signal reflection and communication errors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, RJ45 form factor, fits directly into the VE.Can port on compatible Victron devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower\u003c\/strong\u003e, passive component, no power or configuration needed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack size\u003c\/strong\u003e, bag of two, giving both terminators required for one VE.Can network segment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 8 g per bag.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Victron devices using the VE.Can interface, including Quattro, Multi, MPPT charge controllers and Cerbo GX.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eA CAN bus network needs termination at each end to function correctly. Without it, signal reflections can cause unreliable data, fault conditions or loss of communication between devices such as inverter\/chargers, MPPT controllers and the GX device. This terminator plugs directly into a spare VE.Can RJ45 port to provide that termination.\u003c\/p\u003e\u003cp\u003eEach VE.Can segment needs exactly two terminators, one at each physical end of the bus. This bag supplies both for a single segment. Larger systems with multiple segments will need additional bags.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eTerminating VE.Can networks in off-grid solar installations using Victron equipment.\u003c\/li\u003e\n\u003cli\u003eCompleting CAN bus wiring in marine and vehicle installations with multiple Victron devices.\u003c\/li\u003e\n\u003cli\u003eCommercial and industrial Victron systems where several devices share a single VE.Can bus.\u003c\/li\u003e\n\u003cli\u003eReplacing lost or damaged terminators in an existing installation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2 x VE.Can RJ45 terminator plugs\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eFit one terminator into the unused VE.Can port on each of the first and last devices in the network chain. Devices in the middle should have both VE.Can ports occupied by network cables, not terminators. Incorrect termination is a common cause of VE.Can communication issues, so check placement if devices are not appearing correctly on the GX device or VRM portal. No tools are required.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061067903264,"sku":"ASS030700000","price":5.66,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030700000-1.webp?v=1785511019"},{"product_id":"victron-mk3-usb-c-interface","title":"Victron MK3-USB-C Interface VE.Bus to USB-C | ASS030140030","description":"\u003cp\u003eThe Victron MK3-USB-C is a hardware interface that connects a computer or laptop to Victron VE.Bus devices via USB-C. Installers and technicians use it to configure, monitor and update firmware on compatible Victron inverters, inverter\/chargers and Multi units through VEConfigure and VictronConnect software.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection type\u003c\/strong\u003e, USB-C on the computer side, VE.Bus (RJ45) on the device side.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFull VE.Bus configuration\u003c\/strong\u003e, required for VEConfigure tasks including transfer switch settings, charge parameters and assistant programming.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFirmware updates\u003c\/strong\u003e, supports firmware updates on VE.Bus inverters and inverter\/chargers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C connector\u003c\/strong\u003e, works directly with modern laptops and computers without an extra adapter.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 80g, compact enough to carry in a tool kit on site.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with the full range of Victron VE.Bus products including MultiPlus, MultiPlus-II, Quattro and related inverter\/charger models.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Bus is Victron's communication protocol used across its inverter\/charger range. Accessing the full configuration depth of these products needs a physical hardware interface between the VE.Bus RJ45 port on the unit and a computer running Victron's configuration software. The MK3-USB-C fills that role, replacing the older MK2 and MK3-USB (Type-A) interfaces with a USB-C variant suited to current hardware.\u003c\/p\u003e\u003cp\u003eVEConfigure, the main tool for configuring VE.Bus devices, needs this interface to talk to the inverter or inverter\/charger. Setting AC input current limits, configuring assistants, adjusting battery charge profiles and updating device firmware all depend on a working MK3 connection. Without it, these settings aren't reachable through any other means on VE.Bus-only products. The interface is also used alongside VictronConnect for certain diagnostic and monitoring functions, and it's a standard item for anyone working regularly with MultiPlus or Quattro systems.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfiguring MultiPlus and MultiPlus-II inverter\/chargers on residential and commercial installations.\u003c\/li\u003e\n\u003cli\u003eProgramming Quattro units in off-grid, hybrid and backup power systems.\u003c\/li\u003e\n\u003cli\u003ePerforming firmware updates on VE.Bus devices during commissioning or servicing.\u003c\/li\u003e\n\u003cli\u003eSetting up assistants such as ESS, generator start\/stop or self-consumption via VEConfigure.\u003c\/li\u003e\n\u003cli\u003eOn-site diagnostics and parameter checks by service engineers.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron MK3-USB-C Interface (VE.Bus to USB-C)\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThis is a configuration and commissioning tool, not a permanent installation component. It should be used by qualified installers familiar with VEConfigure software and VE.Bus system architecture. Incorrect configuration of inverter\/charger parameters can affect system behaviour and safety, so always check firmware and software versions are compatible before updating. No mains or battery wiring is involved in using the interface itself, but the connected inverter\/charger should be handled to its own installation and safety requirements.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061068230944,"sku":"ASS030140030","price":50.06,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030140030-1.webp?v=1785511088"},{"product_id":"victron-ve-direct-cable-10-metre","title":"Victron VE.Direct Cable 10m Data Cable | ASS030530310","description":"\u003cp\u003eThe Victron VE.Direct Cable connects VE.Direct-compatible devices to each other or to a monitoring interface over a 10 metre run. It suits installations where components sit apart, such as a solar charge controller in a battery compartment and a display in a control panel.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 10 metres, for runs a shorter cable will not reach.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtocol\u003c\/strong\u003e, VE.Direct, compatible with Victron MPPT solar charge controllers, BMV battery monitors, Phoenix inverters and other VE.Direct-equipped devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.325 kg, light enough for permanent fitting in vehicles, vessels and fixed off-grid systems.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, VE.Direct proprietary Victron serial interface, plugs directly into VE.Direct ports.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030530310, GTIN 8719076019640, supplied as a single cable ready for use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's point-to-point serial interface, used to carry data between devices such as an MPPT charge controller and a VE.Direct to USB interface, a Color Control GX, a GlobalLink 520, or a dedicated display like the MPPT Control. The cable is passive. It carries no power and needs no configuration, just a plug into each device's VE.Direct port. One cable serves one device connection; monitoring several devices from a single GX unit needs a separate cable for each.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting an MPPT charge controller to a GX monitoring device mounted in a separate enclosure.\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor shunt to a display or GX device across a longer run in a narrowboat, yacht or motorhome.\u003c\/li\u003e\n\u003cli\u003eRouting data cabling through conduit or trunking in a fixed off-grid or backup power installation.\u003c\/li\u003e\n\u003cli\u003eExtending communication reach in larger battery or plant rooms.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron VE.Direct Cable, 10m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis is a data cable and needs no electrical qualification to fit. Check both devices have a free VE.Direct port before ordering. Because VE.Direct is point-to-point, each connected device needs its own dedicated cable. Keep it away from high-current DC wiring where possible to avoid interference.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52061068263712,"sku":"ASS030530310","price":13.35,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030530310-1.webp?v=1785511094"},{"product_id":"victron-remote-on-off-inverting-cable","title":"Victron Inverting Remote On-Off Cable | ASS030550120","description":"\u003cp\u003eThe Victron Energy inverting remote on-off cable reverses the on-off logic signal so compatible Victron inverters and inverter\/chargers can be controlled by systems with opposite polarity output. It solves a common integration problem: when an external switch or automation relay sends a signal polarity that is the inverse of what the Victron remote on-off port expects, the device switches on when it should switch off, and vice versa. This cable corrects that before the signal reaches the unit.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\u003c\/strong\u003e, inverts the remote on-off logic signal for use with opposite-polarity control systems.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, designed for Victron Energy inverters and inverter\/chargers with a remote on-off port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 11g.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation\u003c\/strong\u003e, plug-and-play connection to the remote on-off port, no additional hardware needed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030550120.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076036470.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed where third-party automation or building management systems output a control signal with the wrong polarity for a Victron device, including generator controllers, off-grid and marine installations, and retrofits where existing control wiring cannot easily be changed.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eFitting should be carried out by a qualified electrician or experienced Victron installer. Check compatibility with the specific Victron inverter or inverter\/charger model before connecting, and confirm the remote on-off port is rated for the applied signal. Grid-connected inverter\/charger installations must comply with current UK wiring regulations and any applicable G98 or G99 requirements.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy inverting remote on-off cable (ASS030550120)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095393268000,"sku":"ASS030550120","price":12.47,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030550120-1.webp?v=1785748203"},{"product_id":"victron-galvanic-isolator-16a","title":"Victron Galvanic Isolator VDI-16A Shore Power Earth | GDI000016000","description":"\u003cp\u003eThe Victron VDI-16A galvanic isolator protects boat hulls and shore power wiring from galvanic corrosion. It fits into the shore power earth conductor and blocks low-voltage DC galvanic currents while keeping full AC earth continuity intact. It is rated at 16A continuous, matching a standard single-phase shore power connection.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent rating\u003c\/strong\u003e, 16A continuous, suited to standard single-phase shore power connections.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\u003c\/strong\u003e, blocks DC galvanic currents in the shore earth conductor without interrupting AC earth protection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign\u003c\/strong\u003e, diode-based, with a blocking voltage threshold that stops corrosive currents at source.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 1.15 kg, compact enough for confined bilge or panel spaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e, made by Victron Energy for use with Victron shore power systems.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eHow it works\u003c\/h2\u003e\u003cp\u003eGalvanic corrosion happens when dissimilar metals sit in an electrolyte such as seawater or canal water, connected by a conductive path like the shore power earth cable. Small DC currents travel along that path and slowly eat away at propellers, anodes and hull fittings. The VDI-16A places a pair of blocking diodes in series with the earth conductor. These diodes have a forward voltage drop high enough to stop galvanic currents, typically below 1V, but low enough that the earth conductor still works fully for AC fault protection.\u003c\/p\u003e\u003cp\u003eThe 16A rating matches the most common shore power supply found on UK and European marina pontoons. It fits in-line on the earth conductor inside the vessel, and because it does not interrupt the protective earth under fault conditions it supports the earth continuity principle required by marine electrical standards. Check the specific standard for your vessel type and flag state before fitting.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSailing and motor yachts on marina shore power, canal boats and narrowboats at towpath hook-ups, and any vessel where galvanic corrosion of underwater metalwork is a concern. Also used as a retrofit on vessels without existing galvanic protection.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy Galvanic Isolator VDI-16A\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eFitting must be carried out by a qualified marine electrician familiar with the applicable marine electrical standards, such as BS EN ISO 13297 for European recreational craft. It is wired in-line on the earth conductor of the shore power inlet inside the vessel. Any wiring that bypasses or interrupts the protective earth under fault conditions creates a serious shock hazard, so confirm the installation meets the standard for your vessel type and flag state before use.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095395987744,"sku":"GDI000016000","price":91.33,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-gdi000016000-1.webp?v=1785748529"},{"product_id":"victron-32a-cee-shore-power-adapter","title":"Victron Adapter Cord 32A CEE 5P to 3P Single Phase | SHP307700300","description":"\u003cp\u003eThis Victron adapter cord converts a 32A 3-phase CEE 5-pin shore power supply into a single-phase CEE 3-pin output. It suits marine, motorhome and off-grid setups where the shore connection is 3-phase but the load end only needs single-phase power.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput connector\u003c\/strong\u003e, CEE 5-pin plug, 3-phase, 32A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput connector\u003c\/strong\u003e, CEE 3-pin coupling, single-phase, 32A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent rating\u003c\/strong\u003e, 32A continuous\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.3 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector format\u003c\/strong\u003e, CEE industrial, compatible with standard marina and campsite shore power pedestals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it to connect single-phase onboard chargers or inverter-chargers to a 3-phase marina shore power pedestal, or on motorhome and caravan pitches where only a 3-phase CEE outlet is fitted. It also works for off-grid cabins drawing single-phase power from a 3-phase supply, and for temporary single-phase setups on sites with 3-phase distribution boards.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eThe adapter draws from a single phase of the 3-phase supply, so the pedestal or distribution board must be able to supply at least 32A on that phase. Connection should be carried out by a qualified electrician or marine electrical engineer. Do not exceed the adapter's 32A rating, and check that the single-phase load will not create a significant imbalance across the 3-phase supply.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Adapter cord, 32A 3-phase CEE 5-pin plug to single-phase CEE 3-pin coupling\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095396446496,"sku":"SHP307700300","price":39.24,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp307700300-1.webp?v=1785748594"},{"product_id":"victron-shore-power-plug-16a","title":"Victron 16A\/250Vac Shore Power Plug 2p\/3w | SHP301604000","description":"\u003cp\u003eThis is the Victron Energy replacement plug rated at 16A\/250Vac in a 2-pole\/3-wire configuration, made to mate with Victron's 16A shore power inlets. It suits marine, off-grid and mobile installations that need a secure shore power connection.\u003c\/p\u003e\u003ch2\u003eVictron shore power plug key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRated current\u003c\/strong\u003e, 16A continuous at 250Vac for single-phase AC shore power connections.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfiguration\u003c\/strong\u003e, 2-pole\/3-wire (2p\/3w), carrying live, neutral and earth conductors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFit\u003c\/strong\u003e, designed to mate with Victron Energy 16A power inlets.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.34 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e, genuine Victron Energy component for consistent quality and compatibility within Victron shore power systems.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed for shore power connections on narrowboats, canal boats and leisure craft, and on marine vessels drawing AC supply from a marina or pontoon via Victron inlets. It also suits off-grid cabins and mobile installations built around Victron shore power inlet systems. As a spare part, it replaces a damaged or worn plug on an existing Victron 16A installation.\u003c\/p\u003e\u003ch3\u003eCompatibility note\u003c\/h3\u003e\u003cp\u003eThis is not a universal shore power plug. It is intended specifically for the corresponding Victron 16A inlet, so check the inlet model before ordering.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy 16A\/250Vac 2p\/3w plug\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eWiring must be carried out by a qualified electrician, with correct termination of live, neutral and earth conductors. Marine installations should follow applicable marine electrical standards. Isolate the supply circuit before connecting or disconnecting the plug, and do not use it with inlets or systems it is not rated or designed for.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095397036320,"sku":"SHP301604000","price":64.04,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp301604000-1.webp?v=1785748676"},{"product_id":"victron-mk2-2b-rs232-interface","title":"Victron MK2.2b VE.Bus to RS232 Interface | ASS030120210","description":"\u003cp\u003eThe Victron MK2.2b is a wired interface that converts VE.Bus communication to RS232 serial protocol, letting a PC connect directly to VE.Bus-equipped inverters and inverter\/chargers. It's the tool installers reach for when configuring or updating firmware on Victron's MultiPlus and Quattro ranges through VEConfigure and VEFlash.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtocol conversion\u003c\/strong\u003e, VE.Bus to RS232 for direct PC connectivity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Victron VE.Bus inverters and inverter\/chargers, including MultiPlus and Quattro.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoftware support\u003c\/strong\u003e, enables configuration via VEConfigure and firmware updates via VEFlash.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 40g, easy to keep in a tool kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIdentifiers\u003c\/strong\u003e, SKU ASS030120210, GTIN 8719076019404.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eRS232 remains the standard interface for VEConfigure and VEFlash, and the MK2.2b handles the VE.Bus side of that connection. Installers use it to set system parameters, adjust charge curves, configure parallel or three-phase multi-unit systems, and push firmware updates in the field.\u003c\/p\u003e\u003cp\u003eLaptops and modern PCs without a native RS232 port will need a separate USB-to-RS232 adapter alongside this interface. The MK2.2b only performs the VE.Bus-to-RS232 conversion; it does not provide USB connectivity itself, and it is not a substitute for the VE.Bus Smart Dongle or other wireless monitoring accessories.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfiguring Victron MultiPlus and Quattro inverter\/chargers with VEConfigure.\u003c\/li\u003e\n\u003cli\u003eUploading firmware to VE.Bus devices with VEFlash.\u003c\/li\u003e\n\u003cli\u003eSetting up parallel and three-phase multi-unit systems needing direct serial configuration.\u003c\/li\u003e\n\u003cli\u003eField diagnostics and parameter adjustments by qualified installers.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron MK2.2b VE.Bus to RS232 interface\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis is a configuration and programming tool rather than a permanent installation component, intended for use by qualified installers familiar with VE.Bus systems. Confirm the correct Victron software version is installed on the PC before use, and add a USB-to-RS232 adapter if the host computer lacks a native RS232 port.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095398052128,"sku":"ASS030120210","price":43.86,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030120210-1.webp?v=1785748818"},{"product_id":"victron-shore-power-cord-16a","title":"Victron Shore Power Cord 15m 16A\/250Vac 3x2.5mm² | SHP302501500","description":"\u003cp\u003eThis Victron shore power cord is a 15-metre mains supply cable rated at 16A\/250Vac, built for connecting shore power to marine vessels, motorhomes and off-grid installations. The 3x2.5mm² conductors give it the cross-section needed to carry a full 16A load over this length without excessive voltage drop.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 15 metres, enough reach from shore power pedestals to vessel or vehicle inlets without an extension lead.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 16A\/250Vac, matching standard single-phase shore power supplies used across the UK and EU.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConductors\u003c\/strong\u003e, 3x2.5mm² cross-section, correctly sized for the rated current over this cable length.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 2.66kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrdering\u003c\/strong\u003e, SKU SHP302501500, GTIN 8719076007517.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eMarina pontoon pedestals to yacht or motorboat shore inlets, campsite and motorhome hook-up points, and temporary mains supply for off-grid cabins or site offices. It also works as a replacement shore cord for vessels already fitted with a compatible 16A inlet.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnect only to a shore inlet rated at 16A or higher, with a compatible connector type. The supply end should be protected by an appropriate RCD and overcurrent device. Marine mains connections should be carried out by a qualified marine electrician following applicable wiring standards. Do not use this cable on a supply exceeding 250Vac or 16A.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x Victron Shore Power Cord, 15m, 16A\/250Vac, 3x2.5mm²\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095400214816,"sku":"SHP302501500","price":136.44,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp302501500-1.webp?v=1785749073"},{"product_id":"shore-power-inlet-16a-250vac","title":"Victron Shore Power Inlet 16A 250Vac 2P\/3W | SHP301603000","description":"\u003cp\u003eA polyamide shore power inlet for marine, caravan and off-grid installations that need a weatherproof, panel-mounted AC connection point. Rated at 16A\/250Vac in a 2-pole\/3-wire configuration, it accepts a standard shore power cable and gives a protected mains entry point into a vessel, vehicle or static installation.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 16A at 250Vac, for standard single-phase shore power connections.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfiguration\u003c\/strong\u003e, 2-pole\/3-wire (2P\/3W), covering live, neutral and earth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBody material\u003c\/strong\u003e, polyamide (nylon), resistant to UV exposure, moisture and mechanical impact.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCover\u003c\/strong\u003e, protective cover included, sealing the inlet when no cable is connected.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e, panel-mount design for flush or surface fitting into bulkheads, enclosures or vehicle bodywork.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.23 kg.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThis inlet is the fixed connection point on the vessel or vehicle side of a shore power hookup. Once a shore cable is plugged in, mains AC feeds through to the onboard distribution system, usually via a shore power isolator, RCD or an inverter\/charger such as a Victron MultiPlus or Quattro. The polyamide body suits damp or outdoor locations where a metal fitting isn't wanted.\u003c\/p\u003e\u003cp\u003eThe 2P\/3W wiring carries one live conductor, a neutral and a protective earth, the standard arrangement for single-phase 16A shore connections in leisure marine and caravan use across the UK and EU. A hinged cover keeps the socket face clean and dry when the shore cable is disconnected.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eShore power inlet on sailing yachts, motorboats and canal boats.\u003c\/li\u003e\n\u003cli\u003eMains AC entry point on motorhomes, campervans and caravans.\u003c\/li\u003e\n\u003cli\u003ePanel-mounted AC inlet on off-grid cabins, site offices and portable power enclosures.\u003c\/li\u003e\n\u003cli\u003eReplacement inlet where an existing fitting has degraded.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e1 x Power Inlet Polyamide 16A\/250Vac (2P\/3W)\u003c\/li\u003e\n\u003cli\u003e1 x Protective cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis inlet carries mains AC voltage and should be fitted by a qualified electrician or competent marine\/vehicle electrical engineer. Leisure craft wiring should follow the relevant BS EN ISO marine electrical standards; caravans and motorhomes should follow BS 7671 (IET Wiring Regulations) and applicable leisure vehicle standards. The inlet must be correctly earthed as part of the 2P\/3W circuit, and the cover kept closed whenever the shore cable isn't connected.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095401197856,"sku":"SHP301603000","price":51.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp301603000-1.webp?v=1785749238"},{"product_id":"victron-rj12-data-cable-30cm","title":"Victron RJ12 UTP Cable 0.3m Data Link | ASS030066004","description":"\u003cp\u003eThe Victron RJ12 UTP Cable is a short data cable for linking compatible Victron Energy devices that use an RJ12 interface. At 0.3 m long, it suits panel-mounted or closely spaced installations where a neat, direct connection is needed between components.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ12 (6P6C) on both ends for direct device-to-device connections.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair) construction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.3 m, suited to compact enclosures or side-by-side mounting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.01 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrigin\u003c\/strong\u003e, genuine Victron Energy accessory, made to match Victron device pin-outs.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eRJ12 is a 6-position, 6-contact connector format used across several Victron Energy products for communication between devices. This cable is plug and play, so there is no crimping or field termination needed. Using the Victron-supplied cable avoids the pin-out mismatches that can occur with generic RJ12 leads.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting Victron Battery Monitors, Colour Control GX units, or other RJ12-equipped Victron devices.\u003c\/li\u003e\n\u003cli\u003eShort data links inside battery enclosures or distribution boards.\u003c\/li\u003e\n\u003cli\u003eReplacing a lost or damaged cable on an existing Victron installation.\u003c\/li\u003e\n\u003cli\u003eOff-grid and marine builds where several Victron components sit close together.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ12 UTP Cable, 0.3 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eNo tools are required to fit this cable. Check that both devices use a standard RJ12 (6P6C) interface before connecting. Where it forms part of a larger solar, battery or inverter system, that work should be carried out by a qualified electrician or MCS-accredited installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095401558304,"sku":"ASS030066004","price":5.7,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030066004-1.webp?v=1785749268"},{"product_id":"victron-rj12-utp-data-cable","title":"Victron RJ12 UTP Cable 15m Data Cable | ASS030066151","description":"\u003cp\u003eThis Victron Energy RJ12 UTP cable is a 15 metre communication lead used to connect compatible Victron devices fitted with RJ12 ports. It suits solar, off-grid and battery installations where the monitoring or control panel sits some distance from the main equipment.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 15 m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, RJ12, 6-pin\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.35 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuild\u003c\/strong\u003e, Victron OEM cable made for the RJ12 interface used across the Victron range\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eRJ12 cables link devices such as battery monitors, inverter\/chargers and display panels, carrying low-voltage data rather than power. At 15 m this cable reaches installations where the display or monitor is mounted away from the inverter or battery bank, such as in a separate room or enclosure. Using the Victron-supplied cable keeps the connector terminations and pin configuration correct for the RJ12 interface. A mismatched third-party cable can cause communication faults or damage.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a Victron BMV battery monitor to a remote display panel\u003c\/li\u003e\n\u003cli\u003eLinking Victron inverter\/chargers to monitoring or control panels in off-grid and marine systems\u003c\/li\u003e\n\u003cli\u003eExtending communication runs in motorhomes, caravans and boats\u003c\/li\u003e\n\u003cli\u003eAny Victron installation needing a 15 m RJ12 data connection between compatible devices\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eCheck both devices use RJ12 ports before ordering, since RJ11 connectors look similar but have fewer pins and will not connect. Keep the cable away from high-current DC and inverter output wiring to reduce interference. Fitting the cable itself needs no special qualification, but the wider system should be installed by a qualified electrician or accredited installer.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ12 UTP Cable, 15 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095573066016,"sku":"ASS030066151","price":26.76,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030066151-1.webp?v=1785753845"},{"product_id":"cee-adapter-cord-16a-32a-victron","title":"Victron Adapter Cord CEE 16A Plug to 32A Coupling 250V | SHP307700280","description":"\u003cp\u003eThis Victron Energy adapter cord lets a 16A CEE plug connect into a 32A CEE shore power socket. It suits marine, motorhome and off-grid setups where the shore power outlet does not match the vessel or vehicle's inlet rating.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector format\u003c\/strong\u003e, CEE 16A plug on one end, CEE 32A coupling on the other.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage rating\u003c\/strong\u003e, 250V, for standard single-phase European shore power supplies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.3 kg, easy to store aboard a vessel or in a vehicle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuild\u003c\/strong\u003e, CEE industrial connector format on both ends for a secure connection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eHow it works\u003c\/h2\u003e\u003cp\u003eThe plug and coupling bridge a mismatch between the supply cord and the socket, but current draw stays limited to 16A by the plug rating. This adapter does not raise the available current capacity of the circuit, it only allows the physical connection.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUseful for boats with a 16A shore power inlet needing to plug into a 32A marina pedestal, for motorhomes and campervans with a 16A shore cord at a 32A campsite supply, and for off-grid cabins or temporary sites where the only socket available is 32A CEE. Hire fleets and service engineers also carry these to cover mismatched shore power connections on site.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Adapter Cord with 16A CEE plug and 32A CEE coupling\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eSwitch off the shore power supply before connecting or disconnecting. For fixed shore power installations on vessels, connection should be carried out by a qualified marine electrician following applicable wiring standards.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095573164320,"sku":"SHP307700280","price":28.34,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp307700280-1.webp?v=1785753861"},{"product_id":"shore-power-cord-15m-25a","title":"Victron Shore Power Cord 15m 25A\/250Vac 3x4mm² | SHP304001500","description":"\u003cp\u003eThis Victron shore power cord is a 15 metre mains cable rated 25A\/250Vac, built with 3x4mm² conductors for connecting boats, motorhomes and off-grid installations to a shore power supply.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 15 metres, enough reach from a shore supply to a vessel or vehicle without extension leads\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 25A\/250Vac for single-phase AC connections\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConductor size\u003c\/strong\u003e, 3x4mm² cross-section\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 4kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e, Victron Energy, compatible with standard shore power inlets and connectors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to connect boats and sailing vessels to marina shore power pedestals, and to supply AC power to motorhomes and campervans from campsite hook-up points. It also suits off-grid cabins or site offices needing a temporary mains connection, and pairs with Victron inverter-chargers that take a shore power AC input feed.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eCheck that the shore power inlet, socket and any onboard protection devices are rated to at least 25A before connecting this cable. AC wiring connections should be carried out by a qualified electrician, and marine installations should follow the applicable standards for shore power connections. Do not use this cable with connectors or inlets rated below 25A\/250Vac.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x Victron Shore Power Cord, 15m, 25A\/250Vac (3x4mm²)\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095573295392,"sku":"SHP304001500","price":176.38,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp304001500-1.webp?v=1785753869"},{"product_id":"victron-shore-power-cord-16a-25m","title":"Victron Shore Power Cord 25m 16A\/250Vac 3x2.5mm² | SHP302502500","description":"\u003cp\u003eThis Victron shore power cord runs 25 metres between a marina shore power pedestal and a vessel's onboard AC inlet. Rated 16A at 250Vac with a 3x2.5mm² conductor cross-section, it suits leisure craft, canal boats and liveaboards that need a mains feed at berth.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 25 metres, enough to reach from pedestal to vessel without joining extension leads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 16A at 250Vac, matching standard European and UK marina shore power pedestals.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConductors\u003c\/strong\u003e, 3x2.5mm² cross-section, sized to carry the full 16A rated current with minimal voltage drop over the run.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 3.85kg, a full-length assembly ready for use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand\u003c\/strong\u003e, made by Victron Energy for use with Victron shore power inlets and connectors.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhy a single 25m run matters\u003c\/h2\u003e\u003cp\u003eJoining shorter cords adds connection points, and each one is a place for voltage drop or connector heating to creep in under load. A single correctly rated cord avoids that. At 25 metres, a thinner conductor than 2.5mm² would show a measurable voltage drop that can affect onboard chargers and inverter-chargers, so the cross-section here is chosen to keep losses within acceptable limits across the full length. It is compatible with standard IEC 60309 (CEE) 16A blue connectors found on most European marina pedestals.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed for marina and harbour berth connections on leisure and liveaboard vessels, canal boat and narrowboat pedestal connections, smaller craft needing a 16A shore feed, and temporary shore power during refit or winter lay-up.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnection to a vessel's AC inlet should be done by a qualified marine electrician familiar with BS EN ISO 13297 for small craft electrical systems. Check that the shore pedestal breaker rating matches the cord's 16A rating before connecting, and inspect the cord, connectors and locking collar for wear, cracking or water ingress before each use.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x Victron Shore Power Cord, 25m, 16A\/250Vac, 3x2.5mm²\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095574442272,"sku":"SHP302502500","price":178.52,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp302502500-1.webp?v=1785754042"},{"product_id":"ve-direct-cable-right-angle-10m","title":"Victron VE.Direct Cable 10m Right Angle Connector | ASS030531320","description":"\u003cp\u003eThe Victron VE.Direct cable is a 10 metre data cable for connecting Victron Energy devices fitted with a VE.Direct communication port. One end has a right angle connector, the other a straight connector, which suits installations where cable routing or enclosure space rules out a straight plug on both ends.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 10 metres\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector (end 1)\u003c\/strong\u003e, VE.Direct right angle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector (end 2)\u003c\/strong\u003e, VE.Direct straight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.355 kg\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, any Victron device with a VE.Direct port, including BMV battery monitors, SmartSolar MPPT charge controllers and Phoenix inverters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030531320, GTIN 8719076019701\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's point-to-point serial protocol used across much of its product range. This cable carries data only, not charging power, between a VE.Direct device and an interface such as a VE.Direct to USB adapter, a Color Control GX, or a Raspberry Pi running Venus OS.\u003c\/p\u003e\u003cp\u003eThe right angle end is useful where a device sits flush against a panel or inside a cabinet, and a straight plug would force a sharp bend or stop the enclosure closing. At 10 metres it suits larger layouts such as off-grid cabins, marine vessels or commercial battery rooms where equipment is spread out.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLinking a SmartSolar MPPT controller to a Color Control GX or Cerbo GX across a distributed panel layout\u003c\/li\u003e\n\u003cli\u003eConnecting a BMV battery monitor to a VE.Direct to USB interface for PC monitoring\u003c\/li\u003e\n\u003cli\u003eRouting data cable neatly inside battery enclosures or switchboards where a straight plug would obstruct closure\u003c\/li\u003e\n\u003cli\u003eMarine and motorhome fit-outs where devices sit in confined spaces with a restricted exit angle\u003c\/li\u003e\n\u003cli\u003eOff-grid cabin or commercial installs needing a longer run between monitoring and control gear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Direct cable, 10m, one right angle connector and one straight connector\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis is a data cable and carries no mains or battery voltage, so no specialist electrical qualification is needed to fit it. Route it away from high-current DC cabling where possible to avoid interference, and make sure both connected VE.Direct ports are unpowered before plugging or unplugging. Involve a qualified installer for the wider system where inverters, battery banks or grid-connected equipment are involved.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095574999328,"sku":"ASS030531320","price":13.35,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030531320-1.webp?v=1785754132"},{"product_id":"victron-rj12-communication-cable-30m","title":"Victron RJ12 UTP Cable 30m Communication Cable | ASS030066301","description":"\u003cp\u003eThe Victron RJ12 UTP Cable is a 30 metre communication cable used to link compatible Victron Energy devices over a serial data connection. It suits installations where components sit some distance apart and need a stable, low-noise link between them.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 30 m, for runs between devices mounted across a plant room or battery bank.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, RJ12 (6P6C) at each end for direct plug-in connection to compatible Victron devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction\u003c\/strong\u003e, UTP (Unshielded Twisted Pair), which reduces signal interference along the cable run.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.645 kg.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030066301, GTIN 8719076071594.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eRJ12 is a 6-position, 6-contact connector format that Victron Energy uses for serial communication between devices such as battery monitors, inverter\/chargers and panel displays. A 30 m run lets those devices sit a practical distance apart without extra signal repeaters or custom wiring.\u003c\/p\u003e\u003cp\u003eThe twisted pair construction cuts crosstalk and electromagnetic interference, which matters in battery rooms or plant areas where inverters and chargers generate electrical noise. Using the Victron-supplied cable keeps the connector pinout and cable impedance matched to the device specification, avoiding the communication errors that generic substitutes can cause.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed for connecting battery monitors to remote panel displays, linking inverter\/chargers to control panels in off-grid and hybrid systems, long-run wiring in commercial battery storage rooms, and as replacement or extension cabling on existing Victron installations.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ12 UTP Cable, 30 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eRoute the cable away from high-current DC cables and inverter output wiring to reduce interference. Push RJ12 connectors in fully until the locking tab clicks. This cable carries low-voltage communication signals only, not mains or battery power. Installation should be carried out by a qualified electrician or experienced solar installer familiar with the connected Victron devices.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095575720224,"sku":"ASS030066301","price":28.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030066301-1.webp?v=1785754210"},{"product_id":"victron-can-bus-usb-interface","title":"Victron CANUSB Interface CAN Bus to USB Converter | ASS030532010","description":"\u003cp\u003eThe Victron CANUSB interface is a CAN bus to USB converter for Victron Energy systems. It lets a PC or laptop talk directly to devices on a CAN bus network, for configuration, monitoring and diagnostics without needing a dedicated GX device. It suits installers and engineers who need direct CAN bus access during commissioning or fault-finding.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConverts CAN bus signals to USB for direct PC connectivity\u003c\/li\u003e\n\u003cli\u003eWorks with Victron Energy CAN bus networks used across inverter, battery and BMS installations\u003c\/li\u003e\n\u003cli\u003eWeighs 0.06 kg, suited to use as a portable diagnostic tool\u003c\/li\u003e\n\u003cli\u003eConnects via a standard USB port, no specialist hardware needed beyond a PC or laptop\u003c\/li\u003e\n\u003cli\u003eBus-powered via USB, so no separate power supply is required during use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThe CANUSB interface bridges a CAN bus network and a standard USB port on a Windows PC or laptop. CAN bus is the protocol used between many Victron devices, including certain battery management systems, inverter\/chargers and third-party BMS units. Without a GX device present, direct CAN bus access is otherwise unavailable, which makes this interface a practical tool during commissioning or servicing.\u003c\/p\u003e\u003cp\u003eIt is particularly useful when connecting to battery systems that communicate via CAN bus, such as those using VE.Can or compatible third-party BMS protocols. An installer can read live data, verify communication between devices and carry out configuration directly from a laptop.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect CAN bus communication between a PC and Victron CAN-enabled devices during commissioning\u003c\/li\u003e\n\u003cli\u003eDiagnostics and fault-finding on CAN bus networks in off-grid and battery storage installations\u003c\/li\u003e\n\u003cli\u003eConfiguration of third-party BMS units communicating over CAN bus within a Victron system\u003c\/li\u003e\n\u003cli\u003eMonitoring and data logging from CAN bus devices where no GX device is installed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron CANUSB interface\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eIntended for use by qualified installers and engineers familiar with CAN bus networks and Victron Energy systems. Install the correct software drivers on the PC before use. Follow appropriate electrical safety procedures when working on live battery or inverter systems. This is a diagnostic and configuration tool and should not be left permanently connected in a production installation without confirming compatibility with the system design.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095598821664,"sku":"ASS030532010","price":394.62,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030532010-1.webp?v=1785754543"},{"product_id":"ve-direct-right-angle-cable-victron","title":"Victron VE.Direct Cable 0.3m Right Angle Connector | ASS030531203","description":"\u003cp\u003eA short VE.Direct cable built for tight installations, with one straight connector and one right angle connector so the lead can exit a device port at 90 degrees instead of straight out. At 0.3m long, it is meant for connecting two Victron devices mounted right next to each other, not for running cable across a panel.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 0.3m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, one straight, one right angle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterface\u003c\/strong\u003e, VE.Direct, for Victron devices with a VE.Direct port\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.015kg (15g)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030531203\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076019657\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Direct is Victron's point-to-point serial protocol used to pass data between devices such as MPPT charge controllers, BMV battery monitors, Phoenix inverters and colour control displays. This is the shortest cable in the VE.Direct range, meant for two devices mounted directly alongside one another where a longer cable would only create slack.\u003c\/p\u003e\u003cp\u003eThe right angle end suits a device mounted flush against a wall, inside a cabinet, or on a DIN rail, where a straight-exit cable would either not fit or would put strain on the port. Keeping the exit at 90 degrees holds the cable profile low and avoids bending stress at the connector body.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting an MPPT charge controller to a Cerbo GX or Colour Control GX in the same enclosure\u003c\/li\u003e\n\u003cli\u003eLinking a BMV battery monitor to a display or GX device in a compact panel\u003c\/li\u003e\n\u003cli\u003eShort data runs in van conversions, narrowboats and marine builds where space behind devices is limited\u003c\/li\u003e\n\u003cli\u003eAny VE.Direct setup where a straight connector would protrude into restricted clearance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1x VE.Direct cable, 0.3m, one right angle connector and one straight connector\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003ePower down both devices before connecting or disconnecting VE.Direct cables. This cable carries data only, not power. Check that both devices have a VE.Direct port before ordering, as the interface does not interchange with VE.Bus or VE.Can.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095600296224,"sku":"ASS030531203","price":9.12,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030531203-1.webp?v=1785754696"},{"product_id":"victron-vecan-canbus-bms-type-b-cable","title":"Victron VE.Can to CAN-bus BMS Type B Cable 5m | ASS030720150","description":"\u003cp\u003eThe VE.Can to CAN-bus BMS Type B Cable connects Victron devices fitted with a VE.Can port to compatible CAN-bus BMS battery management systems using the Type B protocol. At 5 metres long, it gives installers room to route between a battery bank and a GX device or inverter\/charger mounted at a distance.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnects VE.Can-equipped Victron devices to CAN-bus BMS batteries using the Type B communication protocol\u003c\/li\u003e\n\u003cli\u003e5 metre length for installations where the BMS and inverter or MPPT sit apart\u003c\/li\u003e\n\u003cli\u003ePre-terminated with the correct connectors at each end, no crimping required\u003c\/li\u003e\n\u003cli\u003eVictron SKU ASS030720150, compatible with the VE.Can interface on Victron MultiPlus-II GX, Quattro, Cerbo GX and other GX-series devices\u003c\/li\u003e\n\u003cli\u003eWeighs 0.22 kg\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eCAN-bus communication between a battery BMS and an inverter\/charger or GX device lets the BMS pass real time data: state of charge, cell voltages, charge and discharge limits, and alarm states. The system can then respond to actual battery conditions instead of fixed charge settings. The Type B variant is needed for BMS units wired to the CAN-bus Type B pinout, which differs from Type A. Fitting the wrong type means no communication, so check the BMS manufacturer's CAN-bus type before ordering.\u003c\/p\u003e\u003cp\u003eThis 5 m option is the longer of Victron's standard lengths for this cable and suits systems where the battery bank and the GX device or inverter are in separate locations. CAN-bus uses differential signalling and tolerates runs of this length where the bus is terminated correctly at both ends.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a Cerbo GX or GX-series device to a CAN-bus Type B BMS battery system\u003c\/li\u003e\n\u003cli\u003eLinking a MultiPlus-II GX or Quattro GX to a compatible third-party lithium battery using CAN-bus Type B\u003c\/li\u003e\n\u003cli\u003eOff-grid and hybrid solar installations where the BMS and inverter\/charger sit apart\u003c\/li\u003e\n\u003cli\u003eMarine and vehicle installations needing a longer run between BMS and Victron control device\u003c\/li\u003e\n\u003cli\u003eBattery cabinet builds where routing adds to the required cable length\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Can to CAN-bus BMS Type B Cable, 5 m\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eConfirm your BMS uses the CAN-bus Type B pinout before fitting. A Type B cable on a Type A port will not communicate and may cause issues depending on the hardware. CAN-bus networks need correct termination at both ends, so check your BMS and Victron documentation for your system's topology. Installation on a solar PV or battery storage system should be carried out by a qualified electrician or accredited installer familiar with Victron equipment.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095601049888,"sku":"ASS030720150","price":10.7,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030720150-1.webp?v=1785754785"},{"product_id":"isolation-transformer-3600w-victron","title":"Victron Isolation Transformer 3600W 115\/230V | ITR040362042","description":"\u003cp\u003eThe Victron Isolation Transformer 3600W 115\/230V is a galvanically isolating transformer built for shore power connections on boats, yachts and shore-tied installations. It breaks the direct earth link between shore supply and vessel, removing the risk of stray current corrosion and electric shock that a hard-wired earth bond can cause.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower rating\u003c\/strong\u003e, 3600W continuous, enough for battery charging, air conditioning and galley loads at once.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual voltage\u003c\/strong\u003e, 115V and 230V on both input and output, so one unit covers UK, European and North American shore supplies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGalvanic isolation\u003c\/strong\u003e, magnetic coupling replaces a direct electrical connection, stopping DC galvanic current flowing through the earth conductor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eToroidal core\u003c\/strong\u003e, keeps flux leakage low and the enclosure compact for its power class.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 21.73 kg, reflecting the core needed for a 3600W toroidal design.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eShore power at a marina normally ties a vessel's earth to every other boat and metal structure sharing that supply. Left unbroken, this forms a galvanic cell that accelerates corrosion of props, stern gear, anodes and hull fittings. This transformer removes that path by transferring AC power magnetically rather than through a direct wire, while the output is re-earthed locally on the vessel side so RCD and earth fault protection on onboard circuits still works as normal.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eShore power on sailing yachts, motor cruisers and live-aboard vessels.\u003c\/li\u003e\n\u003cli\u003eMarina berths where several vessels share a common earth.\u003c\/li\u003e\n\u003cli\u003eShore-tied commercial vessels and workboats needing AC isolation.\u003c\/li\u003e\n\u003cli\u003eInstallations stepping between 115V and 230V shore supplies.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eFitting must be carried out by a qualified marine electrician, wired to BS EN ISO 13297 for recreational craft in the UK and EU. At 21.73 kg the unit needs a structural, vibration-damped mounting surface with ventilation clearance, and the shore supply must be isolated at the pedestal before any connections are made.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Isolation Transformer 3600W 115\/230V\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095601148192,"sku":"ITR040362042","price":406.33,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-itr040362042-1.webp?v=1785754801"},{"product_id":"victron-power-inlet-32a-250vac","title":"Victron Power Inlet Stainless Steel 32A\/250Vac 2p\/3w | SHP303202000","description":"\u003cp\u003eThe Victron Energy stainless steel power inlet is a shore power connection point rated at 32A\/250Vac in a 2-pole\/3-wire configuration. It gives boats, motorhomes and off-grid cabins a weatherproof entry point for shore power, with a hinged cover to keep the socket sealed when not in use.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 32A\/250Vac, suitable for single-phase shore power connections up to 32 amps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfiguration\u003c\/strong\u003e, 2-pole\/3-wire (2p\/3w): live, neutral and earth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial\u003c\/strong\u003e, stainless steel, resistant to corrosion in marine and outdoor settings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCover\u003c\/strong\u003e, hinged protective cover included, sealing the inlet when shore power is disconnected.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e, designed for flush or panel mounting on boats, caravans, motorhomes and off-grid cabins.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with standard IEC 60309-type shore power connectors used at marinas and campsites across the UK and EU.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThis inlet forms the fixed connection point on the vessel or vehicle side of a shore power hookup. Once connected, AC supply passes through to the onboard distribution system, charger or inverter\/charger. The 32A rating suits installations with meaningful continuous AC loads, such as battery chargers, air conditioning or general onboard AC distribution.\u003c\/p\u003e\u003cp\u003eStainless steel is favoured for marine inlets because it withstands salt spray, UV exposure and the wear of repeated plug connections. The hinged cover matters most at the hull or panel penetration, stopping water reaching internal wiring when the boat or vehicle sits disconnected from shore power.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eShore power inlet on sailing yachts, motorboats and canal boats.\u003c\/li\u003e\n\u003cli\u003eShore power connection point on motorhomes and campervans.\u003c\/li\u003e\n\u003cli\u003eAC power entry point on off-grid cabins, site offices and portable power systems.\u003c\/li\u003e\n\u003cli\u003eReplacement inlet on existing marine or vehicle electrical installations.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy stainless steel power inlet 32A\/250Vac (2p\/3w) with hinged cover\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eFitting should be carried out by a qualified electrician or a competent marine electrical engineer, following BS EN ISO 13297 or the relevant standard for the application. Seal the inlet correctly at the panel or hull penetration, and match the shore power supply and onboard wiring to the 32A rating. Check compliance with applicable wiring regulations for the installation type.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095601803552,"sku":"SHP303202000","price":97.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp303202000-1.webp?v=1785754910"},{"product_id":"ve-direct-remote-on-off-cable","title":"Victron VE.Direct Non-Inverting Remote On-Off Cable | ASS030550320","description":"\u003cp\u003eThe VE.Direct non-inverting remote on-off cable lets you control compatible Victron Energy devices externally through the VE.Direct port. It suits installers who need to switch a device on or off remotely without inverting the logic signal, so control behaviour stays straightforward.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLogic type\u003c\/strong\u003e, non-inverting: a high signal on the control input turns the device on, a low signal turns it off, matching standard remote switching conventions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection\u003c\/strong\u003e, plugs directly into the VE.Direct port on compatible Victron devices, no extra interface hardware needed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.11 kg, suitable for compact panel builds and enclosure installations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Victron devices that support remote on-off control via the VE.Direct interface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIdentifiers\u003c\/strong\u003e, SKU ASS030550320, GTIN 8719076036494, supplied as a ready-to-use cable assembly.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThe VE.Direct port on Victron devices carries communication data alongside remote control signals. This cable exposes the remote on-off lines so an external switch, relay or control signal can start or stop the connected device. Because the configuration is non-inverting, the logic follows the input directly, with no inversion circuitry needed in the control wiring.\u003c\/p\u003e\u003cp\u003eThat makes it useful in automated systems where a battery management system, a programmable logic controller, or a simple manual switch needs to control a Victron MPPT charger or similar device. Using the VE.Direct port for this keeps power wiring untouched, which means a tidier install and fewer places for wiring mistakes to creep in.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRemote on-off control of Victron MPPT solar charge controllers in off-grid and marine installations.\u003c\/li\u003e\n\u003cli\u003eIntegration with external BMS or relay outputs to automate switching based on battery state.\u003c\/li\u003e\n\u003cli\u003eManual remote switching of Victron devices from a panel-mounted switch without interrupting power cables.\u003c\/li\u003e\n\u003cli\u003eAutomated control in campervan, narrowboat and off-grid cabin systems where a PLC or timer manages charge cycles.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Direct non-inverting remote on-off cable (ASS030550320)\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eCheck that the target Victron device supports remote on-off control via its VE.Direct port before fitting. Connect the control input to a signal source within the voltage range specified for that device. This is a low-voltage accessory, but it should still be fitted as part of a wider system by a qualified electrician familiar with Victron equipment. Grid-connected or high-voltage battery installations require a qualified installer.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095602229536,"sku":"ASS030550320","price":15.8,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030550320-1.webp?v=1785754975"},{"product_id":"victron-cee-schuko-adapter-cord","title":"Victron Adapter Cord CEE 16A\/250V Plug to Schuko Coupling | SHP307700260","description":"\u003cp\u003eThis Victron Energy adapter cord converts a CEE 16A\/250V shore power plug to a Schuko (Type F) coupling, letting you connect CEE shore supplies to equipment or inlets wired for Schuko. It is a common requirement on boats, motorhomes and off-grid sites where the two connector standards meet.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating\u003c\/strong\u003e, 16A at 250V AC for single-phase shore power\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlug end\u003c\/strong\u003e, CEE 16A (IEC 60309, 2P+E, blue) for shore power pedestals and campsite hookups\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoupling end\u003c\/strong\u003e, Schuko (Type F) for European domestic and marine equipment inlets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.3 kg, compact enough to store aboard a vessel or in a vehicle\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eSolar inverter accessories and shore power\u003c\/h2\u003e\u003cp\u003eCEE and Schuko connectors both appear across European shore power and off-grid installations, but they don't mate directly. This cord bridges the two, feeding a CEE 16A supply into equipment or an inlet terminated in Schuko. It suits boats, campervans and static off-grid setups where the pedestal is CEE but the onboard wiring is Schuko.\u003c\/p\u003e\u003cp\u003eThe 16A\/250V rating matches the standard single-phase supply found at most European marinas, campsites and temporary site connections. It is built for the intermittent connection cycles of leisure and light commercial use rather than continuous industrial loads.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConnecting a boat or narrowboat to a CEE pedestal via a Schuko inlet\u003c\/li\u003e\n\u003cli\u003eAdapting campsite or marina CEE hookups for Schuko-terminated motorhome or caravan inlets\u003c\/li\u003e\n\u003cli\u003eTemporary site power where CEE supply and Schuko equipment are both in use\u003c\/li\u003e\n\u003cli\u003eOff-grid cabins and static installations needing a CEE to Schuko interface\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Adapter Cord 16A\/250V CEE Plug to Schuko Coupling\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis is a plug-and-use adapter, no hardwiring needed. Isolate the shore supply before connecting or disconnecting, and check that supply voltage and frequency suit the connected equipment. For permanent shore power wiring on a vessel, use a qualified marine electrician familiar with the relevant regulations.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095602360608,"sku":"SHP307700260","price":18.72,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-shp307700260-1.webp?v=1785754990"},{"product_id":"rj12-utp-communication-cable-5m","title":"Victron RJ12 UTP Cable 5m Communication Lead | ASS030066050","description":"\u003cp\u003eThis Victron Energy RJ12 UTP cable gives you a 5-metre data link between compatible Victron devices fitted with an RJ12 port. It suits installers connecting battery monitors, display panels and control units across off-grid, marine or vehicle-based systems.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 5 metres, enough reach across most battery cabinets or control panels without needing an extension.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector\u003c\/strong\u003e, RJ12, for direct fit with Victron devices using this interface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable type\u003c\/strong\u003e, UTP (Unshielded Twisted Pair) construction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 0.109 kg, easy to route through confined enclosures or cable trays.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU\u003c\/strong\u003e, ASS030066050.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse it to connect Victron battery monitors to compatible display panels, link control units in off-grid solar installations, or wire Victron components in marine and vehicle setups. It also works as a replacement where an existing cable has been damaged or is too short.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eCheck that your Victron device actually uses an RJ12 port before ordering, since the range uses several connector types. Keep the cable away from high-current DC wiring to reduce the risk of signal interference. System-level wiring should be carried out by a qualified electrician or accredited installer.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x Victron Energy RJ12 UTP Cable, 5 m\u003c\/li\u003e\u003c\/ul\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095602393376,"sku":"ASS030066050","price":12.81,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030066050-1.webp?v=1785754996"},{"product_id":"vecan-to-nmea2000-micro-c-cable","title":"Victron VE.Can to NMEA2000 Micro-C Male Cable | ASS030520200","description":"\u003cp\u003eThis cable connects a Victron device fitted with a VE.Can port directly to an NMEA 2000 network backbone, using a Micro-C male connector on the NMEA 2000 end. It plugs straight into a standard Micro-C T-piece or backbone drop point, with no extra adaptor or gateway needed.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, VE.Can on the Victron device end, Micro-C male on the NMEA 2000 end.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, fits standard Micro-C backbone sockets and T-pieces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight\u003c\/strong\u003e, 59 g (0.059 kg).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number\u003c\/strong\u003e, Victron ASS030520200.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGTIN\u003c\/strong\u003e, 8719076019534.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eVE.Can is the CAN-bus interface used on Victron products such as MultiPlus-II, Quattro, Cerbo GX and various MPPT charge controllers. NMEA 2000 is the marine standard for linking onboard electronics like chartplotters and displays. This cable bridges the two, letting Victron data such as battery state, inverter status and charger data appear on an NMEA 2000 network without a separate gateway.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIntegrating a Cerbo GX or CCGX into a vessel's NMEA 2000 network for system-wide monitoring.\u003c\/li\u003e\n\u003cli\u003eShowing Victron battery, inverter or charger data on a compatible marine chartplotter or multifunction display.\u003c\/li\u003e\n\u003cli\u003eMarine off-grid and hybrid power systems where Victron equipment needs to talk to existing onboard electronics.\u003c\/li\u003e\n\u003cli\u003eSailing and motor vessel installations that need power and navigation data pulled together.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1 x VE.Can to NMEA 2000 Micro-C male cable\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eFitting should be carried out by someone familiar with both NMEA 2000 topology and VE.Can configuration. Check the network backbone is correctly terminated at both ends before adding drop devices, and confirm the VE.Can port is enabled in VictronConnect or Venus OS before connecting.\u003c\/p\u003e","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":52095602426144,"sku":"ASS030520200","price":54.59,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-ass030520200-1.webp?v=1785755003"}],"url":"https:\/\/www.ledandsolar.co.uk\/collections\/victron-cables-accessories.oembed","provider":"LED \u0026 Solar","version":"1.0","type":"link"}