{"title":"Pylontech","description":"\u003cp\u003ePylontech make lithium iron phosphate batteries for home and off-grid solar storage. We stock the low voltage US series for 48V systems, the high voltage Force H2 modules for hybrid inverters that run a higher DC bus, and the parts that go around them.\u003c\/p\u003e\u003cp\u003eThe US2000C at 2.4kWh and the US5000 at 4.8kWh stack in parallel, so a system can start small and grow later. Larger kits ship as pre-built packs with an indoor cabinet. We also carry the pieces that are easy to forget: mounting brackets, battery extension cables, BMS communication leads and genuine replacement BMS boards.\u003c\/p\u003e\u003cp\u003eAll of these batteries are LiFePO4, the chemistry chosen for domestic storage because it tolerates partial charging and lasts for thousands of cycles. If you are not sure which model suits your inverter, our solar team will check compatibility before you order.\u003c\/p\u003e","products":[{"product_id":"force-h3x-6kw-hybrid-inverter","title":"Pylontech Force H3X 6kW Hybrid Solar Inverter MPPT","description":"\u003cp\u003eThe Pylontech Force H3X FH3X6K-HY-1P is a single phase hybrid solar inverter and battery storage system rated at 6kW, built for solar self-consumption, grid import and export, smart tariff switching and backup power. This hybrid solar inverter pairs directly with Pylontech FH10050 high voltage LiFePO4 battery modules stacked vertically beneath the unit.\u003c\/p\u003e\u003ch2\u003ePylontech Force H3X hybrid inverter overview\u003c\/h2\u003e\u003cp\u003eThe inverter, BMS and energy management electronics are combined into one enclosure. Pylontech promotes a fast, simplified installation process of around 15 minutes on a properly prepared site, carried out by a qualified installer. The battery connection is wire-free, using an internal bus bar rather than separate power or communication cables between inverter and battery modules.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eNominal power\u003c\/strong\u003e, 6kW single phase output\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery compatibility\u003c\/strong\u003e, Pylontech FH10050 high voltage LiFePO4 modules, stacked vertically\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrid interaction\u003c\/strong\u003e, CT clamp based monitoring of import and export, without a separate Eastron meter for standard operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackup power port\u003c\/strong\u003e, supplies selected essential loads during a mains outage\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSmart tariff support\u003c\/strong\u003e, Intelligent Dynamic mode adjusts charging and discharging around tariff periods, including time-of-use pricing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign\u003c\/strong\u003e, integrated inverter, BMS and energy management with fewer external components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to home solar battery storage, solar self-consumption, smart import and export tariffs, backup power for essential circuits, and small offices, warehouses or commercial buildings using high voltage battery storage. The Force H3X platform can expand across residential and small commercial systems, subject to system design and manufacturer limits.\u003c\/p\u003e\u003ch2\u003eInstallation\u003c\/h2\u003e\u003cp\u003eThis is professional installation equipment. Grid connection, backup wiring, CT connection, DNO notification and electrical protection must all be completed by a qualified, competent installer in line with local regulations and the manufacturer's installation manual.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52053853864224,"sku":"003029","price":1363.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-003029-1.webp?v=1785421043"},{"product_id":"pylontech-extension-cable-1500mm","title":"1500mm Battery Extension Cable Red\/Black | Pylontech US5000 US2000","description":"\u003cp\u003eThese 1.5 metre extension cables let you connect Pylontech battery banks in parallel over greater distances than the standard short interconnect leads allow. Fitted with Amphenol connectors in red and black, they are compatible with all Pylontech battery types, including the US5000 and US2000 ranges.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 1500mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, Amphenol, male\/female, colour coded red\/black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with all Pylontech battery models, including US5000 and US2000\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePurpose\u003c\/strong\u003e, extends reach for parallel connection between battery piles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse these cables where battery piles are positioned further apart than the standard cable length permits, keeping parallel strings correctly linked without straining the original interconnects.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eDC battery cable connections should only be carried out by a qualified electrician. Always verify polarity before connecting to avoid damaging the battery bank.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060309422368,"sku":"PYL1500MM","price":58.43,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pyl1500mm-1.webp?v=1785487599"},{"product_id":"pylontech-us5000-mounting-brackets","title":"Pylontech Mounting Brackets 1 Pair | US2000 \u0026 US5000 Batteries","description":"\u003cp\u003eGenuine Pylontech mounting brackets for the US2000 and US5000 battery range, sold as a pair, enough for one battery. They let you stack multiple batteries vertically into a tower, cutting the floor footprint of a battery bank and keeping cable runs tidy.\u003c\/p\u003e\u003ch2\u003eKey features of these Pylontech mounting brackets\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine part\u003c\/strong\u003e, manufactured by Pylontech, not a third-party equivalent.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePair included\u003c\/strong\u003e, two brackets per pack, sufficient for mounting one battery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, fits both US2000 and US5000 batteries (select the correct model at checkout).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStacking\u003c\/strong\u003e, designed for vertical tower installations of multiple batteries.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed when wall-mounting or stacking Pylontech US2000 and US5000 batteries in a tower configuration, typically in lithium-ion battery storage installations where floor space is limited and a clean, vertical cable layout is wanted.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"for US5000","offer_id":52060309487904,"sku":"002296","price":49.35,"currency_code":"GBP","in_stock":true},{"title":"for US2000","offer_id":52060309520672,"sku":"90914402","price":36.75,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-90914402-1.webp?v=1785487610"},{"product_id":"pylontech-force-h2-battery-module","title":"Pylontech Force H2 FH9637M 3.55kWh High Voltage Battery Module","description":"\u003cp\u003eThe Pylontech Force H2 FH9637M is a high voltage LiFePO4 battery module for residential and commercial energy storage systems. It operates at 96V nominal and delivers 3.55kWh per module, with the modular design allowing systems to be built from 7.1kWh up to 85.2kWh by stacking modules vertically. The lightweight, compact build simplifies installation. Price is per module.\u003c\/p\u003e\u003ch2\u003ePylontech force h2 battery module features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 3.55kWh per module\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage\u003c\/strong\u003e, 96V nominal, high voltage system\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry\u003c\/strong\u003e, LiFePO4 (lithium iron phosphate)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eScalability\u003c\/strong\u003e, expandable from 7.1kWh (2 modules) up to 85.2kWh (24 modules)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign\u003c\/strong\u003e, vertically stacked, lightweight and compact\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePricing\u003c\/strong\u003e, sold per single module\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to high voltage residential energy storage paired with compatible hybrid inverters, and to commercial systems that need a scalable high voltage battery bank built from multiple modules.\u003c\/p\u003e\u003ch3\u003eInstallation and safety notes\u003c\/h3\u003e\u003cp\u003eHigh voltage battery systems carry dangerous voltages. Installation and commissioning must be carried out by a qualified electrician experienced with high voltage ESS, following Pylontech installation guidance and IET Wiring Regulations.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060310044960,"sku":"FH9637M-FH2-1","price":829.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fh9637m-fh2-1-1.webp?v=1785487693"},{"product_id":"pylontech-us5000-bms-board","title":"Genuine BMS Replacement Board | Pylontech US5000 Lithium Battery","description":"\u003cp\u003eThis is a genuine replacement BMS board for the Pylontech US5000 lithium battery. It fits the US5000 only and must be fitted by an authorised Pylontech engineer. Voltacon is an authorised Pylontech partner and one of the UK's designated repair centres for Pylontech lithium batteries.\u003c\/p\u003e\u003ch2\u003eGenuine Pylontech US5000 BMS board\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, designed for the Pylontech US5000 lithium battery only.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine part\u003c\/strong\u003e, supplied as an official Pylontech replacement board.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting\u003c\/strong\u003e, must be installed by an authorised Pylontech engineer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplier\u003c\/strong\u003e, provided through Voltacon, an authorised Pylontech UK repair centre.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation and safety notes\u003c\/h2\u003e\u003cp\u003eFitting this board is restricted to Pylontech-authorised engineers. Replacing the BMS without authorisation may void the battery warranty. Lithium batteries hold dangerous voltages and energy levels, so DIY replacement is not permitted.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to restore a faulty BMS on an existing Pylontech US5000 battery within a lithium-ion storage system, keeping the battery within its original specification and warranty terms.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060310176032,"sku":"002608","price":208.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-002608-1.webp?v=1785487714"},{"product_id":"pylontech-us2000c-48v-battery","title":"Pylontech US2000C 48V 2.4kWh Lithium Ion Phosphate Battery","description":"\u003cp\u003eThe Pylontech US2000C is a 48V lithium iron phosphate battery with a 2400Wh nominal capacity, built for stacking into larger home and small commercial energy storage banks. This model has now been discontinued by Pylontech and is no longer in production, so it is shown here for reference and for owners maintaining existing systems.\u003c\/p\u003e\u003ch2\u003eKey features of the Pylontech US2000C lithium battery\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eNominal voltage\u003c\/strong\u003e, 48V nominal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNominal capacity\u003c\/strong\u003e, 2400Wh, 2280Wh usable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCell chemistry\u003c\/strong\u003e, LFP (Lithium Iron Phosphate)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCycle life\u003c\/strong\u003e, greater than 2000 cycles at 25°C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, CAN BUS \/ RS485\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eParallel capability\u003c\/strong\u003e, up to 8 units in parallel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDiscontinued status and current alternatives\u003c\/h2\u003e\u003cp\u003ePylontech has withdrawn the US2000C from production. For a new installation, Pylontech's current range includes the US3000C at 3.55kWh 48V with 95% DoD and a 10-year warranty, the US5000C at 4.8kWh 48V 100Ah with an improved C rate and 10-year warranty, and the Pelio-L at 5.12kWh 48V with IP65 protection and Wi-Fi monitoring for indoor or outdoor fitting. All three can be stacked in parallel arrangements up to 16 units.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eWhere still in service, the US2000C sits within off-grid and hybrid battery banks alongside compatible inverters using CAN BUS or RS485 communication, cased at 442 x 410 x 89mm and weighing 24kg per unit.\u003c\/p\u003e\u003cp\u003eVoltacon is an authorised Pylontech UK distributor and can advise on sizing a replacement bank around the US3000C, US5000C or Pelio-L.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060310602016,"sku":"US2000","price":682.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-us2000-1.webp?v=1785487776"},{"product_id":"pylontech-us5000-battery-cabinet-192kwh","title":"Indoor Battery Cabinet for 4x Pylontech US5000 19.2kWh Black","description":"\u003cp\u003eThis indoor battery cabinet holds four Pylontech US5000 48V lithium batteries, giving 19.2kWh of protected energy storage inside a black finish enclosure. It suits homes and offices where the battery bank needs to stay out of sight but still look tidy.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, houses 4x Pylontech US5000 batteries for 19.2kWh total storage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish\u003c\/strong\u003e, premium black metallic exterior.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e, shields batteries from dust and mechanical knocks.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse\u003c\/strong\u003e, built for indoor installation in homes and offices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFootprint\u003c\/strong\u003e, compact design for tighter plant rooms or utility spaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eFits residential and commercial installs using Pylontech US5000 batteries where the storage needs to sit indoors, protected and presentable.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eBattery connections must be carried out by a qualified electrician. This cabinet is for indoor use only, and the batteries' operating temperature range should be observed at all times.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060311847200,"sku":"CBN-US5000-B","price":756.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-cbn-us5000-b-1.webp?v=1785487993"},{"product_id":"pylontech-us3000c-battery-kit-14-2kwh","title":"Pylontech US3000C 14.2kWh Battery Kit | White Cabinet","description":"\u003cp\u003eA complete 14.2kWh lithium energy storage kit built around four Pylontech US3000C LiFePO4 batteries, housed in a white metallic cabinet with a transparent front door. Everything needed to connect the system is included, and the cabinet footprint is less than 1 square metre. The whole kit arrives on a pallet.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBatteries\u003c\/strong\u003e, 4x Pylontech US3000C, 3.55kWh each, 14.2kWh total\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCabinet\u003c\/strong\u003e, white metallic finish with transparent front door\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower cables\u003c\/strong\u003e, 2x sets of 2m battery power cables included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, BMS and inter-communication cables included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e, fuse disconnector and battery fuses included, plus earth wires\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCertification\u003c\/strong\u003e, certified for indoor domestic use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential lithium energy storage, whether paired with solar generation or used to shift consumption onto off-peak tariffs. The compact cabinet footprint makes it practical for utility rooms and similar indoor spaces.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eAll connections must be made by a qualified electrician. The cabinet is intended for indoor use only, and the battery operating temperature range must be observed during installation and use.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e4x Pylontech US3000C batteries in white cabinet\u003c\/li\u003e\n\u003cli\u003e2x sets of 2m battery power cables\u003c\/li\u003e\n\u003cli\u003eBMS and inter-communication cables\u003c\/li\u003e\n\u003cli\u003eFuse disconnector, battery fuses and earth wires\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060311945504,"sku":"US3000-PACK-14KWH","price":5347.13,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-us3000-pack-14kwh-1.webp?v=1785488006"},{"product_id":"pylontech-us5000-15kwh-battery-kit","title":"Pylontech US5000 Pack of 3 15kWh Battery Storage Kit","description":"\u003cp\u003eA complete 15kWh lithium energy storage kit built around three Pylontech US5000 batteries, each rated at 4.8kWh. The kit is supplied with the racks, cables and protection gear needed to get the bank wired and mounted without sourcing separate parts.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery bank\u003c\/strong\u003e, 3x Pylontech US5000 4.8kWh batteries, 15kWh total capacity\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty\u003c\/strong\u003e, 10 years on the batteries\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower cables\u003c\/strong\u003e, 2m power cable pair included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBMS cable\u003c\/strong\u003e, communication cable included for battery management\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e, 200A Mersen fuse disconnector and fuses included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e, 3x genuine Pylontech wall mounting brackets included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e3x Pylontech US5000 batteries\u003c\/li\u003e\n\u003cli\u003e2m power cables and BMS cable\u003c\/li\u003e\n\u003cli\u003e200A Mersen fuse disconnector and fuses\u003c\/li\u003e\n\u003cli\u003e3x Pylontech mounting brackets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to 15kWh energy storage in off-grid and hybrid solar systems, where a pre-matched set of batteries, cabling and racking simplifies the install.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eAll connections must be made by a qualified electrician. Check BMS cable compatibility with your inverter before ordering.\u003c\/p\u003e\u003cp\u003eVoltacon is an authorised Pylontech UK distributor.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060312338720,"sku":"3-PACK-US5000","price":2719.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-3-pack-us5000-1.webp?v=1785488078"},{"product_id":"pylontech-us3000c-lithium-battery-48v","title":"Pylontech US3000C 3.55kWh 48V Lithium Battery 95% DoD","description":"\u003cp\u003eThe US3000C is a 3.55kWh 48V lithium iron phosphate battery from Pylontech, built for solar storage systems that need reliable, stackable capacity. With a 95% depth of discharge and a 10-year warranty, it's a proven unit already installed in thousands of systems across the UK and Europe.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUsable capacity\u003c\/strong\u003e, 3.55kWh at 95% depth of discharge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage\u003c\/strong\u003e, 48V nominal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eParallel operation\u003c\/strong\u003e, up to 16 units, no external communication hub required\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery management\u003c\/strong\u003e, advanced BMS with equal cell charging\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty\u003c\/strong\u003e, 10 years, registerable online using part number US3000C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrack record\u003c\/strong\u003e, deployed in over 5,000 UK and European installations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential and commercial solar setups running hybrid or off-grid inverters, where it works alongside compatible inverter brands as part of a wider battery bank. Voltacon is an authorised Pylontech UK distributor.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnections must be made by a qualified electrician. Check BMS cable compatibility with your inverter before installing.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060312371488,"sku":"US3000","price":892.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-us3000-1.webp?v=1785488088"},{"product_id":"48v-lithium-battery-cabinet-15kwh","title":"Lithium Battery Cabinet 15kWh 48V | Pylontech US2000C","description":"\u003cp\u003eThis cabinet houses Pylontech US2000C LiFePO4 batteries in a protected indoor enclosure, delivering 15kWh at 48V. The Silent Power cabinet starts from 7.5kWh and can be expanded up to 60kWh, and this listing is now supplied with US2000C batteries only.\u003c\/p\u003e\u003ch2\u003eKey features of this 48v lithium battery\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery cells\u003c\/strong\u003e, Pylontech US2000C LiFePO4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 15kWh, expandable from 7.5kWh to 60kWh\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign life\u003c\/strong\u003e, 10 years\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry\u003c\/strong\u003e, maintenance-free sealed LFP\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e, Silent Power metallic indoor cabinet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCabling\u003c\/strong\u003e, BMS communication and power cables included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential energy storage across off-grid, hybrid and grid-tied solar systems, where a sealed lithium battery bank is needed indoors.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnections must be made by a qualified electrician. An inverter is sold separately. The battery operating temperature range must be observed when installing indoors.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"15kWh - 6x Batteries \u0026 Cabinet","offer_id":52060312797472,"sku":"0610877897735","price":4095.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-0610877897735-1.webp?v=1785488151"},{"product_id":"us5000c-battery-48v-100ah","title":"Pylontech US5000C Lithium Ion Battery 4.8kWh 48V 100Ah","description":"\u003cp\u003eThe Pylontech US5000C is a 4.8kWh 48V 100Ah lithium iron phosphate battery built for residential and commercial solar energy storage. It offers a 95% depth of discharge and an improved C rate over earlier Pylontech models, with up to 100A maximum continuous charge and discharge current. Pylontech recommends 80A for everyday use to balance performance with long-term battery protection.\u003c\/p\u003e\u003ch2\u003eKey features of the Pylontech US5000 lithium ion battery\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 4.8kWh at 95% depth of discharge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage\u003c\/strong\u003e, 48V nominal, 100Ah\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemistry\u003c\/strong\u003e, LiFePO4 (lithium iron phosphate)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent\u003c\/strong\u003e, up to 100A maximum continuous charge\/discharge, 80A recommended\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eScalability\u003c\/strong\u003e, up to 16 units in parallel, no external hub required\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty\u003c\/strong\u003e, 10 years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cp\u003eThe US5000C communicates with most BMS-enabled hybrid and off-grid inverters, with a built-in Smart BMS that handles cell balancing and prevents overcharge or overdischarge. Units can be stacked using rack systems or mounting brackets, and installation can be vertical or horizontal, indoors or outdoors.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential and commercial solar energy storage, and to hybrid or off-grid inverter battery banks where scalable, stackable capacity is needed.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eConnections must be made by a qualified electrician. Check BMS cable compatibility with your specific inverter model before installation.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060313354528,"sku":"US5000","price":819.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-us5000-1.webp?v=1785488251"},{"product_id":"pylontech-us5000-battery-cabinet-20kwh","title":"Pylontech US5000 20kWh Lithium Battery Cabinet Kit","description":"\u003cp\u003eA complete 20kWh lithium energy storage kit built around 4 Pylontech US5000 4.8kWh batteries. It comes with a metallic cabinet, all power and BMS cables, a fuse disconnector and 200A fuses, ready for a clean and protected installation next to a compatible off-grid or hybrid inverter. Voltacon is an authorised distributor of Pylon Technologies.\u003c\/p\u003e\u003ch2\u003ePylontech US5000 battery cabinet features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery bank\u003c\/strong\u003e, 4x Pylontech US5000 4.8kWh 48V 100Ah batteries, 20kWh total\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCabinet\u003c\/strong\u003e, metallic enclosure available in white or black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCables\u003c\/strong\u003e, 2m power cables and BMS communication cable included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShort pair cables\u003c\/strong\u003e, 50cm from fuse disconnector to inverter\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e, 200A Mersen fuse disconnector with 2x fuses\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInter-battery links\u003c\/strong\u003e, all link cables between batteries included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e4x Pylontech US5000 batteries\u003c\/li\u003e\n\u003cli\u003e1x metallic cabinet (white or black)\u003c\/li\u003e\n\u003cli\u003ePower cables, BMS cable, short pair cables\u003c\/li\u003e\n\u003cli\u003e200A Mersen fuse disconnector and fuses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to 20kWh home or commercial energy storage, paired with off-grid and hybrid solar inverters.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eAll connections must be made by a qualified electrician. The inverter is sold separately. Contact us for 0% VAT supply and installation enquiries.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060315844896,"sku":"4-PACK-US5000","price":4294.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-4-pack-us5000-1.webp?v=1785488523"},{"product_id":"pylontech-lv-hub-communication-hub","title":"Pylontech LV Hub 48V Battery Parallel Communication Hub","description":"\u003cp\u003eThe Pylontech LV Hub is a communication hub for 48V battery banks that need more than 16 US-series batteries connected in parallel. It handles RS485 and CAN communication between the connected battery groups and the inverter, so the BMS can manage the whole bank correctly once it grows past the 16-unit limit.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRequired for 48V systems with more than 16 batteries in parallel\u003c\/li\u003e\n\u003cli\u003eEach hub connects up to 5 battery piles\u003c\/li\u003e\n\u003cli\u003eRS485 and CAN communication bus\u003c\/li\u003e\n\u003cli\u003eCompact dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eFits large Pylontech battery banks that exceed 16 units in a 48V system. Used in commercial and high-capacity residential off-grid and hybrid installations where multiple battery piles need to communicate as one bank.\u003c\/p\u003e\u003ch3\u003eWhy it's needed\u003c\/h3\u003e\u003cp\u003eWithout the LV Hub, the BMS cannot correctly manage systems above 16 units. Adding a hub for every 5 additional piles keeps communication between the battery groups and the inverter working as the bank scales up.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060316205344,"sku":"LV-HUB","price":577.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-lv-hub-1.webp?v=1785488566"},{"product_id":"pylontech-battery-cable-kit-2m","title":"Pylontech Battery Cables 2m 25mm² | RJ45 BMS Communication","description":"\u003cp\u003eThis kit supplies a pair of 2 metre 25mm² battery power cables fitted with Amphenol connectors, along with a 3.5 metre RJ45 BMS communication cable. It is built for linking a Pylontech battery bank to a solar inverter-charger.\u003c\/p\u003e\u003ch2\u003ePylontech battery cables key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower cables\u003c\/strong\u003e, pair of 2m 25mm² cables with Amphenol connectors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication cable\u003c\/strong\u003e, 3.5m RJ45 BMS cable included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, works with Pylontech US2000, US2000C, US3000C and US5000 batteries\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePurpose\u003c\/strong\u003e, connects a Pylontech battery bank to a solar inverter-charger\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUse this cable set when wiring a Pylontech battery bank into a solar inverter-charger setup, whether for a new lithium-ion battery storage install or an upgrade to an existing system.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eDC battery cable connections should only be carried out by a qualified electrician. Check that the BMS cable suits your specific inverter model before ordering, since compatibility varies between inverter brands.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060316729632,"sku":"90914403","price":30.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-90914403-1.webp?v=1785488632"},{"product_id":"pylontech-battery-interconnect-cables-210mm","title":"Short Battery Interconnect Cables 210mm | Pylontech US5000","description":"\u003cp\u003eShort 210mm battery interconnect cables fitted with Amphenol connectors, made for parallel stacking of Pylontech US5000 batteries and other compatible Pylontech models. They link adjacent batteries in a vertical stack.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 210mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector type\u003c\/strong\u003e, Amphenol\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended for\u003c\/strong\u003e, Pylontech US5000\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, suitable for all Pylontech battery types\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\u003c\/strong\u003e, parallel connection of adjacent batteries in a vertical stack\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed when stacking Pylontech US5000 units, or other compatible Pylontech batteries, in a vertical bank. The short length suits adjacent units sitting close together in the stack.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eAll DC battery cable connections must be carried out by a qualified electrician. Check polarity before making any connection.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060316827936,"sku":"PYL210MM","price":32.97,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pyl210mm-1.webp?v=1785488654"},{"product_id":"pylontech-battery-cables-600mm","title":"Pylontech Battery Interconnect Cables 600mm 25mm² | Amphenol","description":"\u003cp\u003eThese Pylontech battery interconnect cables link battery banks together in parallel. Each pair measures 600mm in length with a 25mm² cross-section, fitted with Amphenol connectors for a secure, correctly polarised connection.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength\u003c\/strong\u003e, 600mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCross-section\u003c\/strong\u003e, 25mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, Amphenol, for Pylontech-type batteries\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePair colours\u003c\/strong\u003e, red (positive) and black (negative)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, Pylontech US2000, US3000, US5000 and compatible Dyness and Voltacon battery models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed to interconnect Pylontech and compatible lithium battery banks when wiring them in parallel, forming a larger combined storage bank from individual modules.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eDC battery cable connections should only be carried out by a qualified electrician. Check polarity carefully before connecting anything. Battery DC circuits can carry high fault currents, so care is needed throughout the installation.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060316860704,"sku":"PYL600MM","price":46.31,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pyl600mm-1.webp?v=1785488662"},{"product_id":"pylontech-pelio-l-battery-5-12kwh","title":"Pylontech Pelio-L 5.12kWh 48V LiFePO4 Battery IP65 | Pelio-L","description":"\u003cp\u003eThe Pylontech Pelio-L is a 5.12kWh 48V wall-mounted lithium iron phosphate battery with IP65 weatherproof protection and integrated Wi-Fi monitoring. Built with LFP cell technology, it packs its capacity into a compact, lightweight case suitable for indoor or outdoor mounting. The modular design lets you add further Pelio-L units to grow storage capacity as your needs change.\u003c\/p\u003e\u003ch2\u003eKey features of this 48v lithium battery\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 5.12kWh, 48V LiFePO4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeatherproofing\u003c\/strong\u003e, IP65 rated, suitable for indoor and outdoor installation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMonitoring\u003c\/strong\u003e, integrated Wi-Fi for online monitoring and firmware updates\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFootprint\u003c\/strong\u003e, compact, wall-mounted design\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExpandable\u003c\/strong\u003e, modular, add further Pelio-L units to increase capacity\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCells\u003c\/strong\u003e, latest LFP cell technology for high energy density\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential solar energy storage in grid-tied and hybrid systems, and to off-grid battery storage where an outdoor-rated enclosure is needed.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eWall mounting needs a structurally suitable surface, and all electrical connections must be made by a qualified electrician. For outdoor installation in cold climates, the battery's operating temperature range must be observed.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060317352224,"sku":"002524","price":1018.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-002524-1.webp?v=1785488732"},{"product_id":"pylontech-us2000c-cabinet-2-4kwh","title":"Indoor Silent Power Cabinet for Pylontech US2000C 2.4kWh Batteries","description":"\u003cp\u003eThis indoor metallic cabinet houses Pylontech US2000C lithium batteries for residential energy storage. Each enclosure takes up to 3 US2000C units; for a 6-battery bank you'll need two cabinets side by side.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity per cabinet\u003c\/strong\u003e, holds up to 3 Pylontech US2000C batteries\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction\u003c\/strong\u003e, indoor metallic enclosure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery compatibility\u003c\/strong\u003e, works with Li-2021, US2000 and US2000C battery models\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse case\u003c\/strong\u003e, built for residential indoor lithium-ion battery storage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to homes running Pylontech lithium battery banks where batteries need a tidy, enclosed indoor location rather than open shelving or a rack. Two cabinets side by side cover a 6-battery setup.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eConnections must be carried out by a qualified electrician. Batteries need to be installed within the operating temperature range set out by Pylontech for the US2000C.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060317417760,"sku":"0604947935557","price":672.53,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-0604947935557-1.webp?v=1785488760"},{"product_id":"battery-combiner-box-force-h2","title":"DC Combiner Box 100A IP55 for 6 Pylontech Force H2 Towers","description":"\u003cp\u003eThe Pylontech P-Combiner-HV-6 is a high-voltage DC combiner box that connects up to six Pylontech Force H2 battery towers into a single DC output. It carries a 100A nominal output current at 600V DC, with integrated DC fuses and a main disconnect switch, and is housed in an IP55 \/ NEMA 3S enclosure suitable for indoor or outdoor fitting.\u003c\/p\u003e\u003ch2\u003eBattery combiner box features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTower capacity\u003c\/strong\u003e, connects up to 6 Pylontech Force H2 battery towers in parallel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput rating\u003c\/strong\u003e, 100A nominal output current at 600V DC.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePer-string input\u003c\/strong\u003e, 50A input current per string, with a 150A DC fuse rating per string.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDisconnect switch\u003c\/strong\u003e, integrated main disconnect switch for isolation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e, IP55 \/ NEMA 3S rated, for indoor and outdoor installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating range\u003c\/strong\u003e, -20°C to 55°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompliance\u003c\/strong\u003e, IEC61439-1, IEC61439-2 and UL1741.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions and weight\u003c\/strong\u003e, 400 x 385 x 200mm, 11.7kg.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eLarge residential Pylontech Force H2 installations, commercial and industrial energy storage systems, and multi-tower high-voltage battery arrays that need organised DC distribution all benefit from a single protected output rather than a custom busbar arrangement.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThis combiner box is designed for use with Pylontech Force H2 batteries only. Installation must be carried out by a qualified electrical engineer experienced with high-voltage DC battery systems, with correct cable sizing, fusing and earthing. Follow the Pylontech Force H2 system installation guide for wiring configuration and commissioning.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060754084128,"sku":"P-Combiner-HV-6","price":724.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-p-combiner-hv-6-1.webp?v=1785503775"},{"product_id":"bms-board-us2000c-battery","title":"BMS Replacement Board for Pylontech US2000C 48V 2.4kWh Battery","description":"\u003cp\u003eThis genuine BMS (Battery Management System) board is a replacement part for the Pylontech US2000C 48V 2.4kWh lithium battery. It is compatible with the US2000C only and must be fitted by an authorised engineer. Voltacon, an authorised Pylontech partner and UK repair centre, supplies the board along with installation instructions after purchase.\u003c\/p\u003e\u003ch2\u003eKey features of the Pylontech US2000C BMS board\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine replacement BMS board for Pylontech US2000C\u003c\/li\u003e\n\u003cli\u003eCompatible with US2000C (48V 2.4kWh) only\u003c\/li\u003e\n\u003cli\u003eRestores cell voltage monitoring, protection and inverter communication\u003c\/li\u003e\n\u003cli\u003eCommunicates with the inverter via RS485 and CAN interfaces\u003c\/li\u003e\n\u003cli\u003eSupplied by a Pylontech authorised partner and UK repair centre\u003c\/li\u003e\n\u003cli\u003eInstallation instructions provided by Voltacon upon purchase\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhy the board fails\u003c\/h2\u003e\u003cp\u003eA faulty BMS board can cause the battery to shut down unexpectedly, lose communication with the inverter, or report an incorrect state of charge. Fitting a genuine Pylontech board restores correct operation of cell balancing, temperature monitoring and over-current protection.\u003c\/p\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePylontech US2000C 48V 2.4kWh only\u003c\/li\u003e\n\u003cli\u003eNot compatible with US2000B, US3000C, US5000 or any other Pylontech model\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation and safety\u003c\/h2\u003e\u003cp\u003eThis board must only be fitted by an authorised engineer. Internal components of a lithium battery carry dangerous voltages, and incorrect installation can cause electric shock, fire or permanent damage to the battery. Contact Voltacon after purchase for the correct installation instructions before starting work. Do not attempt self-installation.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060756640032,"sku":"PCB-US2000C","price":156.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pcb-us2000c-1.webp?v=1785504155"},{"product_id":"h3x-hybrid-solar-inverter-battery","title":"Pylontech Force H3X 6kW Hybrid Solar Inverter with LiFePO4 Battery","description":"\u003cp\u003eThe Pylontech Force H3X is a 6kW hybrid solar inverter built into a single stack with vertically mounted LiFePO4 battery modules. Storage starts at 5.12kWh per module and expands to 35kWh in one stack, with a maximum system capacity of 210kWh across multiple groups. Because the inverter sits directly on top of the battery tower, a full 35kWh system takes up less than 2 square metres of floor space.\u003c\/p\u003e\u003ch2\u003eKey features of the pylontech force h3x hybrid system\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverter output\u003c\/strong\u003e, 6kW hybrid inverter with grid-parallel and off-grid operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery chemistry\u003c\/strong\u003e, LiFePO4 modules, expandable from 5.12kWh to 35kWh per stack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaximum capacity\u003c\/strong\u003e, up to 210kWh across multiple stacked groups\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFootprint\u003c\/strong\u003e, inverter mounted on the battery stack, under 2m² for a full 35kWh system\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation\u003c\/strong\u003e, suitable for indoor and outdoor mounting\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCertification\u003c\/strong\u003e, G98\/G99 (UK) and compliant with European installation standards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEnergy management\u003c\/h2\u003e\u003cp\u003ePylontech's Dynamic Control EMS tracks energy flow in real time and adjusts charging and discharging to increase self-consumption and cut grid import. The system runs in parallel with the grid under normal conditions and switches to off-grid operation automatically if the grid goes down. A free mobile app is included for remote monitoring and control.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential installations where floor space is limited, small commercial energy storage projects, and grid-connected systems used for self-consumption and backup power. The stackable design also suits sites where storage needs may grow over time.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eGrid connection must meet G98 or G99 requirements depending on system size. The battery stack needs a level, solid floor able to support the full loaded weight, and all wiring should be carried out by a qualified installer following the Pylontech Force H3X installation guide. The battery module reference is FH10050.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"5kWh","offer_id":52060759130400,"sku":"FH3X5-5K","price":2056.95,"currency_code":"GBP","in_stock":true},{"title":"10kWh","offer_id":52060759163168,"sku":"FH3X5-10K","price":3249.75,"currency_code":"GBP","in_stock":true},{"title":"15kWh","offer_id":52060759195936,"sku":"FH3X5-15K","price":4226.25,"currency_code":"GBP","in_stock":true},{"title":"20kWh","offer_id":52060759228704,"sku":"FH3X5-20K","price":5202.75,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fh3x5-5k-1.webp?v=1785504343"},{"product_id":"pelio-l-ground-mount-cable-kit","title":"Pylontech Pelio-Kit-G Ground Mount Kit for Pelio-L-5.12","description":"\u003cp\u003eThe Pylontech Pelio-Kit-G is the official ground mount installation kit for the Pelio-L-5.12 low-voltage battery module. It supplies the hardware and cables needed to floor-mount up to four Pelio modules in a stable vertical stack, with a maximum supported weight of 200kg.\u003c\/p\u003e\u003ch2\u003ePylontech cable kit contents\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting base\u003c\/strong\u003e, 1x PELIO mounting base\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStability hardware\u003c\/strong\u003e, 2x anti-tipping brackets and 2x handle baffles\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower cables\u003c\/strong\u003e, 2.5m positive and 2.5m negative, 4AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication cables\u003c\/strong\u003e, 2.5m RS485 RJ45 and 2.5m CAN RJ45, plus a 1.5m LINK cable for stacking\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding cable\u003c\/strong\u003e, 2.0m, 6AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixings and covers\u003c\/strong\u003e, M8x60 expansion screws, TSP120-R waterproof covers, RJ45 terminals, power terminal covers, module top covers, Wi-Fi block, wiring brackets and assorted screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cp\u003eDesigned specifically for Pylontech Pelio-L-5.12 LV battery modules. Supports stacks of up to four modules, with a combined weight limit of 200kg.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eFit the kit on a level, solid floor able to bear the full loaded weight of the stack. Follow the Pylontech Pelio-L installation guide for the correct stacking sequence, cable routing and torque values. All electrical connections should be carried out by a qualified installer.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePELIO mounting base, anti-tipping brackets and handle baffles\u003c\/li\u003e\n\u003cli\u003ePower, RS485, CAN, grounding and LINK cables as listed above\u003c\/li\u003e\n\u003cli\u003eWi-Fi block, expansion screws, waterproof covers, RJ45 terminals, terminal covers, module top covers and assorted wiring hardware\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060759654688,"sku":"002525","price":187.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-002525-1.webp?v=1785504461"},{"product_id":"fh3x-hybrid-solar-inverter-battery","title":"Pylontech Force FH3X 3.6kW Hybrid Solar Inverter | 5.12kWh Battery","description":"\u003cp\u003eThe \u003cstrong\u003ePylontech Force FH3X\u003c\/strong\u003e pairs a 3.6kW hybrid inverter with a stackable LiFePO4 battery module in one integrated unit. Storage starts at 5.12kWh and can be expanded to 15kWh by adding further modules underneath the inverter, which sits directly on top of the battery to keep the footprint compact. The system is certified to G98\/G99 for UK grid connection and can be installed indoors or outdoors.\u003c\/p\u003e\u003ch2\u003eKey features of this hybrid solar inverter with battery\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverter output\u003c\/strong\u003e, 3.6kW hybrid inverter with grid-parallel and off-grid operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery capacity\u003c\/strong\u003e, LiFePO4 module, expandable from 5.12kWh to 15kWh\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFootprint\u003c\/strong\u003e, inverter mounts on top of the battery module in a single stack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation\u003c\/strong\u003e, suitable for indoor and outdoor siting\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnergy management\u003c\/strong\u003e, Pylontech Dynamic Control EMS with a free mobile app for remote monitoring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompliance\u003c\/strong\u003e, certified to G98\/G99 (UK) and EU standards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eHow it works\u003c\/h2\u003e\u003cp\u003eDuring normal operation the FH3X runs in parallel with the grid, drawing on solar and stored battery power to cover household demand and cut grid import. If the grid goes down it switches automatically to off-grid mode to keep connected loads running. The Dynamic Control EMS handles charging and discharging in real time to make the most of self-consumption.\u003c\/p\u003e\u003cp\u003eBecause the battery and inverter form one stack, cabling stays short and the install stays tidy. A second battery module takes storage to 10.24kWh, and a third to 15kWh, with no change needed to the inverter or wiring.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eResidential solar energy storage\u003c\/li\u003e\n\u003cli\u003eGrid-connected self-consumption with backup power\u003c\/li\u003e\n\u003cli\u003eProperties where installation space is limited\u003c\/li\u003e\n\u003cli\u003eStarter systems with a planned future battery expansion\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eGrid connection must meet G98 or G99 requirements (UK) depending on system size. The battery stack needs a level, solid floor, and all electrical work should be carried out by a qualified installer following the Pylontech Force FH3X installation guide.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"5kWh","offer_id":52060759687456,"sku":"FH3X3.6-5K","price":2310.0,"currency_code":"GBP","in_stock":true},{"title":"10kwh","offer_id":52060759720224,"sku":"FH3X3.6-10K","price":3360.0,"currency_code":"GBP","in_stock":true},{"title":"15kwh","offer_id":52060759752992,"sku":"FH3X3.6-15K","price":4410.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fh3x3-6-5k-1.webp?v=1785504475"},{"product_id":"bms-board-us3000c-replacement","title":"BMS Replacement Board for Pylontech US3000C Lithium Battery","description":"\u003cp\u003eGenuine replacement BMS (Battery Management System) board for the Pylontech US3000C 48V 3.55kWh lithium battery. It is compatible with the US3000C only and must be fitted by an authorised engineer. Voltacon is an authorised Pylontech partner and one of the UK's repair centres for Pylontech lithium batteries.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine part\u003c\/strong\u003e, official replacement BMS board for the Pylontech US3000C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel fit\u003c\/strong\u003e, compatible with US3000C (48V 3.55kWh) only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction restored\u003c\/strong\u003e, cell monitoring, protection and inverter communication returned to normal operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied by\u003c\/strong\u003e a Pylontech authorised partner and UK repair centre\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation instructions\u003c\/strong\u003e provided by Voltacon upon purchase\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThe BMS board manages cell voltage balancing, temperature monitoring, over-current protection and communication with the inverter through the RS485 and CAN interfaces. A faulty board can cause the battery to shut down, lose communication with the inverter, or report an incorrect state of charge. Fitting a genuine Pylontech replacement restores correct operation.\u003c\/p\u003e\u003cp\u003eThis board only fits the US3000C. Contact Voltacon after purchase for the correct installation instructions before any work begins on the battery.\u003c\/p\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePylontech US3000C 48V 3.55kWh only\u003c\/li\u003e\n\u003cli\u003eNot compatible with US2000C, US2000B, US5000 or any other Pylontech model\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation and safety notes\u003c\/h2\u003e\u003cp\u003eThis board must only be fitted by an authorised engineer. Internal components inside a lithium battery carry dangerous voltages. Incorrect installation can cause electric shock, fire or permanent battery damage. Contact Voltacon after purchase for the installation instructions and do not attempt to fit the board yourself.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060759851296,"sku":"PCBUS3000C","price":208.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pcbus3000c-1.webp?v=1785504520"},{"product_id":"pylontech-battery-cables-180mm-kit","title":"Pylontech Battery Cables 180mm | Parallel Connection Kit","description":"\u003cp\u003eShort 180mm power cables for wiring Pylontech batteries together in parallel. The set is suitable for all Pylontech battery types but is particularly recommended for the US2000, given the terminal spacing on that model. Each kit includes a red cable, a black cable and a straight RJ45 BMS communication cable for the battery-to-battery data link.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable length\u003c\/strong\u003e, 180mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable cross-section\u003c\/strong\u003e, 25mm²\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, Pylontech US2000, US3000 and US5000 batteries\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectors\u003c\/strong\u003e, Amphenol-style, matching the Pylontech terminal format\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, includes RJ45 BMS cable for battery-to-battery data link\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e1 x 180mm 25mm² red power cable\u003c\/li\u003e\n\u003cli\u003e1 x 180mm 25mm² black power cable\u003c\/li\u003e\n\u003cli\u003e1 x straight RJ45 BMS communication cable\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eAll battery parallel connections must be made by a qualified installer. Follow the Pylontech installation guide for the correct parallel wiring sequence and torque values. Do not mix Pylontech US-series batteries with other battery brands on the same bus.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060760539424,"sku":"PYL180MM","price":29.82,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-pyl180mm-1.webp?v=1785504742"},{"product_id":"pylontech-fh2-bms-controller-kit","title":"Pylontech Force H2 BMS Controller FC0500M-40S with Base and Cables","description":"\u003cp\u003eThe FC0500M-40S is the Battery Management Unit (BMU) for the Pylontech Force H2 high voltage lithium iron phosphate battery system, also listed as FC0500M-40S-FH2 or FC0500M-40S-V2 depending on kit version. It sits at the top of every Force H2 stack and is essential for correct operation of the tower.\u003c\/p\u003e\u003ch2\u003ePylontech Force H2 battery tower control\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMonitoring and protection\u003c\/strong\u003e, voltage, current, temperature and fault management across the battery tower.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, links the battery tower to the inverter via CAN or RS485.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSystem control\u003c\/strong\u003e, start button, status LEDs and internal relay management.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eParallel operation\u003c\/strong\u003e, link ports allow multiple Force H2 towers to be daisy-chained with one tower acting as master.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eTower configuration\u003c\/h2\u003e\u003cp\u003eOne BMU is required per tower. A standard Force H2 tower is built from 2 to 4 battery modules in series. Each module operates at 96V, so a 4-module tower runs at 384VDC. A minimum of 2 modules per tower is needed for normal operation.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed in high voltage lithium battery storage installations built on the Pylontech Force H2 platform, including systems where multiple towers run in parallel with correct wiring, communication linking and a suitable DC combiner solution.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThe Force H2 system operates between 192V and 384VDC depending on configuration. Installation, wiring and commissioning must only be carried out by a qualified electrical engineer experienced with high-voltage battery storage systems, in line with Pylontech's installation manual and IET Wiring Regulations.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e1x BMU controller FC0500M-40S-FH\u003c\/li\u003e\n\u003cli\u003e1x base for the Force H2 battery stack\u003c\/li\u003e\n\u003cli\u003ePower cables for connecting the tower to the inverter\u003c\/li\u003e\n\u003cli\u003eCommunication cables (CAN and\/or RS485 depending on inverter integration)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060762145056,"sku":"FH9637M-14kwh","price":472.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fh9637m-14kwh-1.webp?v=1785505100"},{"product_id":"pelio-l-wall-mount-cable-kit","title":"Pylontech Pelio-L-5.12 Wall Mount Installation Kit | Pelio-Kit-W","description":"\u003cp\u003eThe Pylontech Pelio-Kit-W is the official wall mount installation kit for the Pelio-L-5.12 low-voltage battery module. It supplies the hardware and cables needed to mount up to three Pelio modules to a wall in a vertical, space-saving arrangement. Power cables, RS485 and CAN communication cables, a grounding cable, wall brackets and fixings are all included.\u003c\/p\u003e\u003ch2\u003ePylontech cable kit contents\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower cables\u003c\/strong\u003e, 1.2m positive and 1.2m negative power cable, 4AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication cables\u003c\/strong\u003e, 2.5m RS485 RJ45 and 2.5m CAN RJ45\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e, PELIO grounding cable included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrackets\u003c\/strong\u003e, PELIO left bracket, right bracket, base, two anti-tipping brackets and two TS51100-Pelio outlet brackets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixings\u003c\/strong\u003e, expansion screws M8x60 (x8), assorted M5x12, M4x6 and M6x16 screws, nylon countersunk screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExtras\u003c\/strong\u003e, four waterproof covers TSP120-R, a Wi-Fi block, two communication ports and two handle baffles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cp\u003eDesigned for Pylontech Pelio-L-5.12 LV battery modules. The kit supports up to three modules per wall installation.\u003c\/p\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cp\u003eThe wall must be structurally capable of supporting the full loaded weight of up to three Pelio modules, using fixings suited to the wall type. Follow the Pylontech Pelio-L installation guide for bracket positioning, cable routing and torque values. Electrical connections should be made by a qualified installer.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52060768469280,"sku":"002554","price":187.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-002554-1.webp?v=1785505987"},{"product_id":"a300-hy-commercial-battery-storage","title":"Pylontech A300 HY Commercial BESS 300kWh 400Vac 156.8-1565kWh","description":"\u003cp\u003eThe Pylontech A300 HY is a commercial battery energy storage system with an integrated hybrid inverter, built for high power applications, electricity arbitrage, demand response and long-duration backup. Output is 400Vac three phase, with scalable capacity from 156.8kWh up to 1565kWh across multiple cabinets.\u003c\/p\u003e\u003ch2\u003eCommercial battery storage with integrated hybrid inverter\u003c\/h2\u003e\u003cp\u003eLFP lithium chemistry and intelligent energy management sit behind a 1000V DC system, giving 96% round-trip efficiency at 0.5C-rate and 98% depth of discharge. Cycle life is rated at more than 7000 cycles, and transfer time between on-grid and off-grid operation is under 10ms.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAC output\u003c\/strong\u003e, 400Vac three phase\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, scalable from 156.8kWh to 1565kWh\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverter range\u003c\/strong\u003e, 50kW to 500kW depending on configuration\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEfficiency\u003c\/strong\u003e, 96% round-trip at 0.5C-rate, 98% depth of discharge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCycle life\u003c\/strong\u003e, more than 7000 cycles\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e, IP55 outdoor rated with aerosol fire extinguishing and air cooling with controlled HVAC\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eScalable configurations\u003c\/h2\u003e\u003cp\u003eA single cabinet is available at 156.8kWh, 219kWh, 250kWh or 313kWh. Multiple cabinets combine for 626kWh (2), 939kWh (3), 1252kWh (4) or 1565kWh (5), with inverter capacity scaling from 50kW to 500kW depending on inverter quantity. Up to 5 systems can run in parallel.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to factories, warehouses, commercial buildings, EV infrastructure, solar farms and microgrid projects. Operating modes include peak shaving, energy shifting, self-consumption and backup, supporting electricity arbitrage, demand response, grid stabilisation, renewable integration and industrial peak shaving.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52061011771680,"sku":"A300-HY-156KWH","price":40950.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-a300-hy-156kwh-1.webp?v=1785508794"},{"product_id":"leoch-lithium-battery-rack-5kwh","title":"Leoch LR51.2-100 5.12kWh 51.2V 100Ah LiFePO4 Rack Battery","description":"\u003cp\u003eThe Leoch LR51.2-100 is a 5.12kWh rack-mounted LiFePO4 battery built for 48V solar storage. Rated at 51.2V nominal with a 100Ah capacity, it carries a built-in BMS, a front LCD display and RS485, RS232 and CAN communication interfaces, and up to 15 units can be linked in parallel for larger banks.\u003c\/p\u003e\u003ch2\u003eKey features of this leoch battery lithium storage unit\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 5.12kWh usable, 51.2V nominal, 100Ah rated\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCycle life\u003c\/strong\u003e, more than 6000 cycles at 80% depth of discharge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesign life\u003c\/strong\u003e, more than 15 years\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCase\u003c\/strong\u003e, rack-mounted steel case, standard 19-inch rack compatible\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtection\u003c\/strong\u003e, built-in BMS with charge, discharge, overcurrent and temperature protection\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, RS485, RS232 and CAN interfaces, supports up to 15 batteries in parallel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential solar storage, hybrid inverter systems, off-grid PV installations and backup power setups. The rack format fits standard 19-inch cabinets, keeping multi-battery installations tidy, and the front LCD gives a quick read of voltage, current and temperature without opening an app.\u003c\/p\u003e\u003ch3\u003eInverter compatibility\u003c\/h3\u003e\u003cp\u003eLeoch lists compatibility with several inverter brands including Growatt, Sofar, GoodWe, Solis, Victron and Voltronic. This is guidance rather than official approval, so firmware version and BMS protocol should be confirmed before installation.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e1 x Leoch LR51.2-100 5.12kWh rack-mounted LiFePO4 battery\u003c\/li\u003e\n\u003cli\u003eDocumentation and communication cables (check compatibility before ordering)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eRated IP31, this battery must be fitted indoors in a suitable rack, cabinet or protected technical space, not outdoors or in unprotected areas. Follow the Leoch installation guide, use correct DC fusing and cable sizing, and confirm the inverter communication protocol before commissioning. Fitting should be carried out by a qualified installer.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52061011935520,"sku":"LFELI-48100-E16","price":819.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-lfeli-48100-e16-1.webp?v=1785508820"},{"product_id":"pylontech-fidus-pro-bracket-kit","title":"Pylontech Fidus PRO Battery Stacking Bracket Kit 4-Piece Steel","description":"\u003cp\u003eThis is the stacking bracket kit for a floor-mounted Pylontech Fidus PRO 5.12 LV battery tower. Each additional module stacked above the base needs one kit, made up of four steel brackets, two left and two right, that bolt each module to the one beneath it and stop the stack shifting.\u003c\/p\u003e\u003ch2\u003eKey features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility\u003c\/strong\u003e, designed for Pylontech Fidus PRO 5.12 LV battery modules\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eKit contents\u003c\/strong\u003e, 4 steel brackets: 2 left and 2 right, with fixing screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial\u003c\/strong\u003e, steel construction\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixing\u003c\/strong\u003e, screw fixed, no drilling into the batteries required\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage\u003c\/strong\u003e, one kit is needed per additional module above the base unit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eThe brackets fit at the sides of each Fidus PRO module and lock it to the module directly below. Without them, stacked modules aren't mechanically joined to each other, which isn't suitable for a permanent installation. Fitting involves screwing the brackets into the sides of the battery housings, following the Pylontech Fidus PRO installation guide for the correct torque and sequence.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed on Pylontech Fidus PRO 5.12 LV multi-module towers in residential and light commercial solar energy storage systems.\u003c\/p\u003e\u003ch3\u003eInstallation notes\u003c\/h3\u003e\u003cp\u003eModules need to sit on a level, solid floor before the brackets go on. Electrical connections should be made by a qualified installer, and the maximum stack height set by Pylontech should not be exceeded.\u003c\/p\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e4 x steel stacking brackets (2 left, 2 right)\u003c\/li\u003e\n\u003cli\u003eFixing screws\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52061013704992,"sku":"1200300","price":49.35,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-1200300-1.webp?v=1785509075"},{"product_id":"pylontech-a300-hybrid-battery-storage","title":"Pylontech A300 219kWh Commercial Hybrid Battery Storage","description":"\u003cp\u003eThe \u003cstrong\u003ePylontech A300\u003c\/strong\u003e is a \u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003e219kWh\u003c\/span\u003e commercial hybrid battery storage system delivered as a factory-assembled cabinet, ready to connect on site. It suits businesses looking to reduce electricity costs, use more of their own solar generation, and keep running during grid outages or peak demand periods.\u003c\/p\u003e\n\u003ch2\u003eKey features of this commercial battery storage system\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, \u003cmeta charset=\"utf-8\"\u003e\n\u003cspan\u003e219kWh\u003c\/span\u003e LFP battery in a single factory-assembled cabinet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInverter options\u003c\/strong\u003e, available with 1 or 2 hybrid inverters depending on site power needs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e, IP55-rated outdoor cabinet with integrated active cooling\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl\u003c\/strong\u003e, integrated EMS for charge and discharge management\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety\u003c\/strong\u003e, built-in fire protection and battery management system\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse cases\u003c\/strong\u003e, solar self-consumption, peak shaving, electricity arbitrage and grid backup\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eProduct overview\u003c\/h2\u003e\n\u003cp\u003eAt \u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003e219kWh\u003c\/span\u003e the A300 gives sites with heavy daily consumption a large energy reserve. It stores energy when solar output is high or import tariffs are lower, then discharges it during expensive peak periods or when the grid drops out, cutting bills and adding resilience.\u003c\/p\u003e\n\u003cp\u003eA single inverter covers most standard storage and self-consumption applications. The dual inverter configuration is for sites with higher peak loads, faster charging needs, or where stronger backup is required for critical circuits.\u003c\/p\u003e\n\u003cp\u003eBattery modules, BMS, cooling, safety protection and energy management are all integrated and factory tested before the cabinet leaves the factory, so there's no need to source and wire individual components on site.\u003c\/p\u003e\n\u003ch2\u003eApplications\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eCommercial premises: offices, warehouses, factories and retail sites\u003c\/li\u003e\n\u003cli\u003eAgricultural sites and farms with solar PV\u003c\/li\u003e\n\u003cli\u003eEV charging hubs needing grid buffering or off-peak charge storage\u003c\/li\u003e\n\u003cli\u003eIndustrial sites with high peak demand requiring load smoothing\u003c\/li\u003e\n\u003cli\u003eMicrogrid and partial off-grid commercial installations\u003c\/li\u003e\n\u003cli\u003eSites needing long-duration backup for critical loads\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eInstallation notes\u003c\/h2\u003e\n\u003cp\u003eThis system must be installed by a qualified electrical engineer experienced in commercial battery storage. Site assessment, load analysis, grid connection compliance and commissioning need to be handled by a certified installer. Get in touch to discuss inverter configuration and site suitability before ordering.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52061014524192,"sku":"A300-HY-219KWH","price":36225.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-a300-hy-216kwh-1.webp?v=1785509188"},{"product_id":"pylontech-fidus-pro-battery-5-12kwh","title":"Pylontech Fidus Pro 5.12kWh LiFePO4 Battery IP65 Self Heating","description":"\u003cp\u003eThe Pylontech Fidus Pro FB-L-5.12-EU-Pro is a low-voltage lithium battery for solar storage, built on the LiFePO4 chemistry that underpins the well-known US5000C platform. It adds stronger environmental protection, self-heating, modern monitoring and an IP65 anti-corrosive housing for installations that go beyond a standard indoor rack.\u003c\/p\u003e\u003cp\u003eNominal capacity is 5.12kWh with intelligent BMS protection, suiting residential solar storage, off-grid systems, backup power, hybrid inverter setups, garages, outbuildings and plant rooms.\u003c\/p\u003e\u003ch2\u003ePylontech Fidus Pro key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 5.12kWh nominal, 51.2V low-voltage LiFePO4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelf-heating\u003c\/strong\u003e, integrated heating function for cold weather operation, enabled by default and manageable via battery controls or the app\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating range\u003c\/strong\u003e, -20°C to 55°C on the Pro heating model\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHousing\u003c\/strong\u003e, IP65-rated enclosure with C5-M anti-corrosion protection for indoor, outdoor and humid environments\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, CAN and RS485 for compatible low-voltage hybrid and off-grid inverters, plus Wi-Fi, LED and Bluetooth monitoring options\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent\u003c\/strong\u003e, 100A continuous charge and discharge, peak 120A for 2 minutes and 200A for 15 seconds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCycle life\u003c\/strong\u003e, 8000 cycles at 25°C \/ 0.5C per manufacturer data\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExpandable\u003c\/strong\u003e, up to 20 batteries in one string and up to 6 strings with suitable system design\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCold weather and housing\u003c\/h2\u003e\u003cp\u003eThe heating system can bring the battery from -20°C to at least 5°C in approximately 2 hours, depending on system power availability and operating conditions. The IP65 housing and C5-M anti-corrosion coating suit garages, utility rooms, outbuildings, workshops and covered outdoor or dusty locations where a standard indoor-only battery would struggle.\u003c\/p\u003e\u003ch2\u003eInstallation and expansion\u003c\/h2\u003e\u003cp\u003eThe Fidus Pro can be wall-mounted, rack-mounted or installed in a floor-standing stacked arrangement, depending on accessories used. One unit gives 5.12kWh; larger systems can combine up to 20 batteries per string and up to 6 strings with the correct communication hub.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eResidential solar battery storage\u003c\/li\u003e\n\u003cli\u003eHybrid inverter systems\u003c\/li\u003e\n\u003cli\u003eOff-grid solar PV systems\u003c\/li\u003e\n\u003cli\u003eBackup power systems\u003c\/li\u003e\n\u003cli\u003eGarage, plant room and outbuilding installations\u003c\/li\u003e\n\u003cli\u003eExpandable battery banks for larger storage projects\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation notes\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eInstallation must be carried out by a competent and qualified installer\u003c\/li\u003e\n\u003cli\u003eMust not be connected directly to AC power\u003c\/li\u003e\n\u003cli\u003e51.2V DC low-voltage system, must not be connected in series\u003c\/li\u003e\n\u003cli\u003eThe battery system must be correctly grounded\u003c\/li\u003e\n\u003cli\u003eBattery, inverter and communication settings must be compatible before commissioning\u003c\/li\u003e\n\u003cli\u003eA Pylontech LV-Hub may be required for multi-string systems\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52061015802144,"sku":"Fidus-US5000D","price":880.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fidus-us5000d-1.webp?v=1785509419"},{"product_id":"pylontech-fidus-pro-20kwh-battery","title":"Pylontech Fidus Pro 20kWh LiFePO4 Battery Stack IP65","description":"\u003cp\u003eThe Pylontech Fidus Pro is a 20kWh low voltage LiFePO4 battery stack built from 4 x 5.12kWh modules, each rated at 51.2V. It carries an IP65 enclosure, C5-M anti-corrosion protection and a built-in self-heating function, making it a practical choice for garages, utility rooms, outbuildings and other spaces where a standard indoor-only battery would struggle.\u003c\/p\u003e\u003ch2\u003ePylontech Fidus Pro key features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCapacity\u003c\/strong\u003e, 20kWh total from 4 x 5.12kWh modules\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage\u003c\/strong\u003e, 51.2V low voltage LiFePO4 chemistry\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelf-heating\u003c\/strong\u003e, Pro version heating function for operation down to -20°C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure\u003c\/strong\u003e, IP65 rated with C5-M anti-corrosion protection\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMonitoring\u003c\/strong\u003e, Wi-Fi module with Pylontech App support\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommunication\u003c\/strong\u003e, CAN and RS485 for compatible hybrid and off-grid inverters\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct overview\u003c\/h2\u003e\u003cp\u003eCompared with the standard indoor rack battery format, the Fidus Pro is designed for sites where moisture, dust, cold temperatures or corrosive air are a factor. The self-heating function manages heating automatically once low temperature conditions are detected, and manufacturer data states the battery can heat from -20°C to at least 5°C in around 2 hours, depending on available system power and site conditions.\u003c\/p\u003e\u003cp\u003eThe BMS includes cell balancing and active safety management. According to manufacturer data the battery is rated for 8000 cycles at 25°C \/ 0.5C. The system can be expanded to up to 20 batteries in one string, with up to 6 strings supported where the wider system design and communication hub allow it.\u003c\/p\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eSuited to residential solar battery storage, hybrid inverter systems, off-grid solar PV installations and backup power setups, including larger expandable energy storage projects that call for a stack of several modules working together.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52095612027168,"sku":"Fidus-20KWH","price":3465.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fidus-20kwh-1.webp?v=1785756056"},{"product_id":"high-voltage-lifepo4-battery-module","title":"Pylontech FH10050 5.12kWh High Voltage LiFePO4 Battery Module","description":"\u003cp\u003eThe Pylontech FH10050 is a 5.12kWh high voltage battery module built with lithium iron phosphate (LiFePO4) cells. It forms part of the Pylontech Force H3 and Force H3X high voltage battery platform, with a nominal module voltage of 102.4V and a stackable design that lets installers build larger battery banks for residential and small commercial solar storage.\u003c\/p\u003e\u003ch2\u003eHigh voltage battery module for Force H3 \/ H3X systems\u003c\/h2\u003e\u003cp\u003eModules connect using an internal bus-bar system rather than external cabling, so a stack of FH10050 units links together without loose wiring between them. This keeps installation tidy and supports vertical expansion within an approved system configuration.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e5.12kWh energy per module, 102.4V nominal voltage\u003c\/li\u003e\n\u003cli\u003e50Ah battery module capacity\u003c\/li\u003e\n\u003cli\u003eLithium iron phosphate (LiFePO4) cell chemistry\u003c\/li\u003e\n\u003cli\u003eStackable, wire-free bus-bar interconnection between modules\u003c\/li\u003e\n\u003cli\u003eDesign life of 15+ years\u003c\/li\u003e\n\u003cli\u003eUp to 8,000 cycles under defined operating conditions\u003c\/li\u003e\n\u003cli\u003eModule dimensions 540 x 350 x 170mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplications\u003c\/h2\u003e\u003cp\u003eUsed for solar PV self-consumption, hybrid inverter battery storage, residential and small commercial energy storage, and time-of-use tariff shifting. Backup power operation is possible where the connected inverter supports it.\u003c\/p\u003e\u003cp\u003eA compatible BMS and inverter are required. This module works with the Pylontech FH3X-8K-HY-1P-EU, FH3X-10K-HY-3P-EU, FH3X-12K-HY-3P-EU and FH3X-15K-HY-3P-EU inverters. For stand-alone storage with Solis or other compatible inverters, the external FH2 BMS (FC0500M) is required.\u003c\/p\u003e\u003ch3\u003eImportant installation note\u003c\/h3\u003e\u003cp\u003eThis is a high voltage battery module for use only within an approved Pylontech Force H3 or Force H3X system. It is not a 48V low voltage battery and must not be wired directly to low voltage inverters. Installation must follow the official Pylontech manual and approved inverter compatibility list, carried out by a qualified installer.\u003c\/p\u003e\u003ch3\u003eWhat's in the box\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e1 x Pylontech FH10050 high voltage battery module\u003c\/li\u003e\n\u003cli\u003eManufacturer documentation where supplied\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eController, inverter, base, power cables and communication accessories may be needed depending on the full system and are not included unless stated in the product options.\u003c\/p\u003e","brand":"Pylontech","offers":[{"title":"Default Title","offer_id":52095616811296,"sku":"FH10050","price":871.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1010\/8148\/1504\/files\/ledandsolar-fh10050-1.webp?v=1785756542"}],"url":"https:\/\/www.ledandsolar.co.uk\/collections\/pylontech.oembed","provider":"LED \u0026 Solar","version":"1.0","type":"link"}